Accessing Flash Please Wait message

frugalphone · 2018-07-11T08:42:22.890Z

agreed, but only the list are options, no “Other” or blank on pulldown menu.
Bottom section blued-out; Username pin etc automatically filled out once Provider chosen.
Cannot type anything in, fields are protected, including dialing sequence.
Would be ok, but provider “3” is automatically prefixed in front of “internet” so APN becomes

“3internet” which I cannot overtype and change.

Johnex · 2018-07-11T08:48:12.474Z

Ok lets start from the beginning.
Have you updated the Mifi to the latest firmware? v2.271

If not then download it from here:
http://download.gl-inet.com.s3.amazonaws.com/firmware/mifi/v1/lede-mifi-2.271.bin

Upgrade the firmware.

Reset the mifi by inserting a paper clip gently into the reset hole for 10 seconds. The LED of Lan will blink fast at 10 seconds, then release.

Now, once you are on the latest firmware, you should get “Manual” Or “Automatic” configuration of the 3G/4G as soon as you enter the connection info page at the bottom.
If you do automatic, it should work. If it still doesn’t, in the latest firmware it does let me change all the values after they have been filled in.

frugalphone · 2018-07-11T08:56:28.870Z

Updating firmware will be the first thing done, once it’s connected.
I may have gone a step too far now: How can I secure ethernet - only access?
Already password-protected wifi then turned wifi off.
But mifi could be used, just by turning it on and having an ethernet cable, couldn’t it?
So I changed to require phone pin, then changed the pin (did this in a phone).
Oops, now it won’t boot to where it was before, so there must not be a way to key a pin to the sim?
Thinking about it, that would be difficult – ok, thanks for indulging newbie dumb queries!

Johnex · 2018-07-11T08:59:01.812Z

Ok so remove the Pin using the phone again, cos i had this issue. I would get no internet if i had a pin on the sim, something with the modem module or some bug somewhere.

Try without a pin and see if you get internet

frugalphone · 2018-07-11T10:18:26.262Z

Oh dear. Changed back so original sim pin and also pin is not requested.
Won’t connect. I think it did connect before, should have changed pin.
(sigh) Changed pin to original again, set to not request pin, which works on phone (phone doesn’t request pin) but still not working.

Might this be related?
Left column under “Settings” - next to globe icon, is completely blank. In help section this is filled in with “Internet Status”.
In tab Repeater, the SSID is blank and will not let me type either GL-MIFI-777 (original) or (I____) which was what I changed it to. Does this Repeater SSID need to be filled in?

Still not connecting, but it was, according to Provider help desk who checked - saw it connect an hour ago, now nothing

Johnex · 2018-07-11T16:46:42.563Z

Try to reset the Mifi like i wrote before and start from the beginning?

frugalphone · 2018-07-11T18:06:01.563Z

Reset many times (and also earlier too), all possible combinations: with / without sim, Wifi LED on / not on, right after power up, holding reset for up to 1.5 minutes.
lan LED flashes at 3 different speeds **while reset button is pressed **then off, which usually confirms the reset has completed, but not reset.

LEDs do not flash in pattern after I release reset.
Mifi does not reboot after I press reset.

Even the new name of wifi has not been reset to GL-MIFI-777, its still what I changed it to. Also called service provider who changed sim from data sim back to a normal phone sim, then back to data sim (thinking something was in cache stuck on their side).

Mifi not reset at all, the default password does log me in, only the password that I set logs me in.
So mifi does not reset.

All this happened after I changed sim to require a pin (<<== my bad), so is there a correlation?

Johnex · 2018-07-11T18:19:49.002Z

You are not doing the reset properly. You count to 10 in your head and it will be flashing fast. You release then, not wait until it stops flashing.

frugalphone · 2018-07-11T18:44:45.843Z

OK, have tried that also, still not reset.
Saw that sometimes many resets might finally work – will keep trying, thanks!

Johnex · 2018-07-11T19:01:43.740Z

Try this then?

docs.gl-inet.com

Debrick via Uboot - GL.iNet Docs

Documentation for GL.iNet Productions

For the Mifi it’s 5 blinks like the AR150. As before, you count and when you see the 5th you release quickly, and you get 3 fast blinks telling you it worked.

frugalphone · 2018-07-11T19:23:17.661Z

After many resets, still cannot connect to internet, still not resolved problem. It did clear a few fields but not all.

tab Internet Settings, SSID is still blank (was GL-MIFI-777)
Wireless Settings, Mode was still new 150M (11ng) not original 72M (11ng)
Wifi password was still there.
Also tried “reset Modem” from Internet Status page, under Modem Connection.
if many resets do not clear back to factory settings, anything else to attempt?

Thank you for your help!

frugalphone · 2018-07-11T19:24:16.793Z

Just saw new un-brick doc, trying now

frugalphone · 2018-07-12T00:10:47.627Z

@Johnex, thank you for the un-brick link, well, small progress: Got latest firmware installed. Able to auto configure Model and IMEI, but stuck detecting Carrier. Maybe because my SErvice provider is not on list? A Modem Reset doesn’t fix. Hard reset doesnt fix either.

So I manually update:
Modem Tools > Data > APN = internet and Submit, reboot, but this never seems to be saved even though says “Updating succefully” (sic)
Internet Settings has Modem Device = qmi and APN = internet so I don’t change either one.

And yes, have reset numerous times back to newly installed firmware, updated, submitted, reboot, power off completely but still not connected. AT Tools works, I get all good responses from all Shortcuts. Also power off laptop, still not connect.
New firmware version does show so am assuming am running on 2.271.
Any more ideas besides hard resets and keep trying to update until APN is saved?

Johnex · 2018-07-12T08:21:26.817Z

Well that is how far you will get from the GL-iNet interface.
Now it’s time to go deeper

If you are on windows download Putty. Run it and connect using SSH to the router IP, while you are connected to it with Wifi or Lan

Username is root, password is the password you set for the Web interface.

Run this command first:

uqmi -d /dev/cdc-wdm0 --get-data-status

It will say “disconnected”. Then:

uqmi -d /dev/cdc-wdm0 --get-signal-info

It should say some signal values. If not tell me what it says. If yes, then do:

uqmi -d /dev/cdc-wdm0 --start-network internet --autoconnect

The “internet” in the command is your APN.

Lastly:

uqmi -d /dev/cdc-wdm0 --get-data-status

It should say “connected” hopefully

frugalphone · 2018-07-12T08:57:44.610Z

downloading putty now.
Newbie here: how to connect using SSH?

Johnex · 2018-07-12T08:59:52.155Z

You will see when you start Putty
Select SSH and enter in Host:

root@MIFIIP

Change MIFIIP to the ip of your Mifi. And click open.

frugalphone · 2018-07-12T12:57:57.520Z

OK I’m in, but the APN is failing, the APN is default “internet” but I get “Call failed”.
Oh dear, because this happened when I set the PIN up, I added the PIN back thinking it might work - ok I’ll take pin off and start over – again –

frugalphone · 2018-07-12T12:58:57.038Z

and what happens if / when I get ‘connected’ ? How do I log back off and quit?

Johnex · 2018-07-12T13:00:07.422Z

When you get connected then you are all set. the --auto-connect at the end of the command will tell the modem to connect always when it can.

To log off just close Putty

Then you can go back to the Web UI and check the status there, you should have ip’s, dns and stats

frugalphone · 2018-07-12T13:08:23.932Z

OK thanks . . . I’ve not logged off yet, is there a command to enter the PIN? I changed back to having PIN, in case it might work (since deleting PIN has not worked)