AR750S-EXT Repeater can’t access gui

wcs2228 · 2022-01-30T22:46:47.310Z

If the GL-AR750S is in Router network mode on Admin Panel → MORE SETTINGS → Network Mode, then 192.168.8.1 is the router’s default LAN IP address where you can access the GL.iNet UI from the LAN side.

192.168.1.55 is the router’s WAN IP address which is blocked by the GL.iNet router’s firewall and cannot be accessed from WAN side (i,.e., main router’s side). You have to add port forwarding through the firewall to do so on Admin Panel → FIREWALL.

om3r · 2022-01-30T23:08:17.179Z

Hi,

Router is not in router mode. It’s in Extender mode

wcs2228 · 2022-01-31T00:44:26.108Z

That is strange! Are you able to log in via SSH? You may have to do a reset to factory.

BTW, I always set a Static IP in all my network devices (non-client), instead of having to get an IP from the main router’s DHCP.

om3r · 2022-01-31T02:16:01.697Z

So here what I did.

Hold power button 10sec.to factory default
Router rebooted and I got 192.168.8.x range ip for my laptop
Connected to AR750S-EXT set changed the Network Mode to Extender
It asked me to select my primary Router wifi SSID and password.
AR750S-Ext rebooted and connected to my main Router by wifi
I can ping AR750S-EXT with 192.168.1.X that my DHCP server (primary router) assigned
I can’t connect to GUI…
Tried SSH same problem
I can confirm I have the latest firmware on the device…

wcs2228 · 2022-01-31T02:59:14.318Z

Can you try setting the router to Static IP 192.168.1.55, reboot, then switch to Extender mode?

It seems in the other thread you posted on, you have to open Port 80 for http and Port 22 for ssh through the WAN.

om3r · 2022-01-31T03:12:54.418Z

Hi, on my main router i set the AR750s to a static ip… 192.168.1.55 and rebooted. no luck…

do i need to open port 80 and 22 from the main router?

Also any security concern to opening those ports?

alzhao · 2022-01-31T03:16:14.309Z

Here is the explaination:

The extender mode, uses layer3 relay which caused this behavior. That is when you are connecting to AR750s you cannot access the router’s UI at 192.168.1.x.

But if you set your pc’s IP to static 192.168.8.x and you will be able to access to 192.168.8.1, in extender mode.

When you reset the router, you can just hold for 4 seconds so that it goes from extender mode to router mode without reseting everything.

wcs2228 · 2022-01-31T03:23:43.730Z

Would existing connected clients be disconnected and the router has to be switched back to Extender mode afterwards?

om3r · 2022-01-31T03:38:15.861Z

Confused here… if i leave it in extender mode, i can’t get access to GUI without setting static ip in 192.168.8.x ?? My PC is on wifi to my main router…

wcs2228 · 2022-01-31T03:53:54.814Z

That would be a hassle for sure! I would try what the OP stated in the other thread.

My understanding is:

Set a Static IP for the GL-AR750S itself in the DHCP of the main router.
Open Ports 80 and 22 on the GL-AR750S itself while in Router network mode, before switching to Extender, using Admin Panel → Firewall. There is no security problem because it is all on the LAN.

om3r · 2022-02-01T02:46:12.285Z

I switched to Router network mode, went in Firewall settings and opened port 80 for ip 192.168.1.xx which is my STATIC ip for GL-AR750S. Went back to Extender mode still can’t access the GUI…

wcs2228 · 2022-02-01T02:52:42.438Z

The Port 80 TCP is to be open for all LAN IP addresses, not only for the router IP.

om3r · 2022-02-01T02:54:23.473Z

image2074×674 52.3 KB

wcs2228 · 2022-02-01T02:58:00.183Z

Maybe ask the OP in the other thread how to make it work.

Good reason why I don’t use Extender (only Router and Access Point)

om3r · 2022-02-01T03:01:54.339Z

that’s the only option I think… I have device that has only ethernet port and I am using AR750S to convert the wifi to ethernet so that device can connect but it has to be on same network 192.168.1.xx

wcs2228 · 2022-02-01T03:15:33.381Z

I have done that before with TP-Link TL-WR902AC/TL-WR802N that have “client” mode. Right now, I have a TP-Link RE580D with 4 Ethernet ports connected to main router over 5GHz wifi that gives ~500bps speed … too bad that model has been discontinued.

The GL-AR750S may work in Access Point mode, but I have not tried it.

wcs2228 · 2022-02-01T04:29:36.626Z

Another person wants it also:

Can I use GL-AR750 EXT as wireless bridge? Technical Support for Routers

I’d like GL-AR750 EXT to connect to my network via wifi, but not as a router but as a bridge. In other words, (a) I don’t want GL-AR750 EXT to serve as wifi access point, (b) I want GL-AR750 to extend my network through the LAN ports only, and (c) I don’t want GL-AR750 EXT to operate DHCP server and create its separate network. Are all of these possible? I’ve tinkered with the settings, but couldn’t do it.

alzhao · 2022-02-04T02:45:09.961Z

I just verified that when setting up extender you cannot access its UI using the IP it gets from the main router (192.168.1.x). You can only set static IP on your pc to 192.168.8.x and be able to access 192.168.8.1.

Maybe this is how it works.

shivadow · 2022-02-07T10:05:14.134Z

If the router is assigning the ip addresses then all machines need to be on the same network to be able to see each other. If the router is told that its address is 192.168.8.1 then all machines need to be on the 192.168.8.xxx range. Any other routers connecting to that router need to be on their own range 192.168.xxx.xxx and the gateway of those other routers point to 192.168.8.1. All of which need to be on the SAME subnet mask 255.xxx.xxx.xxx

The PC being on 192.168.1.xxx will stop it from being able to interact on that 192.168.8.xxx network. Change the devices connected to the router to DHCP or put them static on the same network and the network will jump into life.

After thought… Change the gateway address on the PC to 192.168.8.1 and see if that does anything while the rest remains on the 192.168.1.xxx settings.

om3r · 2022-02-07T12:05:23.442Z

Hi thanks for the suggestion, i will try that