AR750s Keeps disconnecting

satirebird · 2021-08-24T11:23:25.887Z

bump on sammo 's question - @satirebird - are you sure the problem is gone?

Yes I am sure. I made several tests using iperf in both directions. With the official firmware the de-authentication happens within the first minute of testing. I had a lot of trouble with that. With the new OpenWRT 21.02.0-rc4 the iperf tests runs without issues (I have tested it for 30 minutes at full load). My AR750S is configured as repeater. The uplink uses a 2.4G link to the router. The client is connected with a 5G link to the AR750S.

Note that I am not using the official glinet release. I am using the plain OpenWRT.

root@OpenWrt:~# uname -a
Linux OpenWrt 5.4.137 #0 Sat Jul 31 17:21:01 2021 mips GNU/Linux

Bildschirmfoto von 2021-08-24 13-15-34904×267 23.6 KB

jason240 · 2021-08-24T16:04:36.380Z

@alzhao can you prepare a test image against 21.02.0-rc4?

alzhao · 2021-08-25T06:32:37.627Z

We are working on firmware 4.x which has many changes. Hopefully we will use 21.02 as the basic openwrt distro.

jason240 · 2021-08-25T06:52:29.996Z

@alzhao do you have a timeline, even for just a test with “yes it boots” beta quality or same version as now with the new kernel patches? I’m trying to avoid going onto openwrt directly and avoiding losing some of the settings I have if you guys can just slap out a test so we get the solution verified for your images. I can update your software builds remotely where as I need to be physically present for the openwrt conversion too.

alzhao · 2021-08-25T11:12:12.355Z

jason240:

I’m trying to avoid going onto openwrt directly and avoiding losing some of the settings I have if you guys can just slap out a test so we get the solution verified for your images. I can update your software builds remotely where as I need to be physically present for the openwrt conversion too.

We should have firmware 4.x beta in end of this year.

diver68 · 2021-08-26T04:34:45.448Z

Had the same problems with GL.Inet FW. Flashed the AR750S to OpenWrt 21.02 RC4, since then no more drops. Repeat on 2.4 and distribute on 5GHz

jason240 · 2021-09-02T03:54:25.676Z

@alzhao confirming it also works reliably for me to use the rc4 from openwrt the others are using. I use 5ghz for my uplink to the other ar750s.

How about you guys just backport the kernel and release an update rather than kicking things out so long.

I have a slight preference for your packaging of openwrt rather than openwrt itself, which kind of gives me both… with this probably don’t have to do travelmate anything either over gl health.

sammo · 2021-09-02T06:43:23.082Z

Repeat on 2.4 and distribute on 5GHz. <= That might work, but set you 5g to non dfs
I use 5ghz for my uplink to the other ar750s. <=. Just be careful it’s a non dfs uplink

On 5g, there is only 1 band which is non dfs or 2 if in usa

NetBeez – 5 Dec 18

Using DFS Channels in WiFi

DFS channels add more usable frequencies for the deployment of WLANs. Before enabling this WiFi function, learn some important implications with radar signals.

alzhao · 2021-09-02T09:12:27.747Z

From here Archer C7 2.4 GHz wireless dies in 24~48 hours - #225 by sammo - Network and Wireless Configuration - OpenWrt Forum

Is the fix increasing memory_limit ?

Seems I cannot get a definite answer on this one.

gokturk · 2021-09-02T20:05:32.353Z

alzhao:

The logs shows the problem of ath10k, not ath9k @satirebird mentioned.

I just tried to use one AR750S to repeat another AR750s on 5G and I don’t have any problem. Both using 3.203 firmware.

Did you every use any mac clone etc. on the router?

I have thrown away the router for since my last post. turned back to old tplink. Today came back because ı needed it for something. And see that you are still insisting that you cannot replicate the problem. Futher you are still fiddling with 5G…turn off 5G man… the problem is 2.4 to 2.4…
best regards…

Also: auto update fails with bad md5 verification… fail…

how could this take soo long?

sammo · 2021-09-02T20:24:58.235Z

@gokturk,. I don’t have ar750s but ar750 which has a slightly different 2.4ghz chipset. To compare notes, with repeater on 2.4ghz do you see in logread beacon loss and then a disconnect?

gokturk · 2021-09-03T12:02:48.836Z

update:

updated to latest firmware. no problems so far in about a day…

(solved the update issue by following all consequtive uptades one by one)

booz · 2021-09-25T12:44:55.804Z

Has anyone had any joy when running an AP on 2.4GHz radio using openwrt 21.02? My recent experience is if I do client on 2.4GHz and AP on 5GHz everything is stable and fine. As soon as I introduce AP onto the 2.4GHz radio the router keeps rebooting itself and only luck lets me get back in and disable that 2.4G AP in order for it to work reliably again. @goturk did you have any luck getting it to work?

booz · 2021-09-27T07:48:57.003Z

I would like to add that although it is relatively stable it still randomly reboots itself after several hours, and most commonly as soon as I log into the luci interface. Free space looks fine. I am running wireguard but nothing else

alzhao · 2021-09-27T11:55:20.131Z

Maybe just try:

A different power adapter

Different WiFi encryption and tax output power

booz · 2021-09-27T12:26:55.897Z

I’ve dropped the output power on both radios to 25mW - seems to be going well so far. Have set WPA2/WPA3 mixed as the encryption

alzhao · 2021-09-27T12:32:47.085Z

WPA3 could be a problem but I am not sure.

booz · 2021-09-28T00:14:38.954Z

update: the unit is now working well - I previously had the power set to 100mW on each radio but clearly that was still too high for the unit to manage reliably. Setting 25mW each is working really well and plenty for coverage in the accomodation we are staying. Made some remote SSH sessions via the router and they have not dropped out. They were connected 15+ hours ago. I’ve got AP running on both 5GHz and 2.4GHz radios. Use case: we are on holiday and have brought down a couple of tasmota-flashed switch plugs. These are MQTT connected back to home assistant at home via the GL-AR750s running wireguard through home pfsense. The switches are working just as nicely as if they were on the local IoT vLAN back at home.

edit- I spoke too soon - the router just rebooted while writing this… however it reconnected straight away

alzhao · 2021-09-28T04:04:14.518Z

booz:

edit- I spoke too soon - the router just rebooted while writing this… however it reconnected straight away

This should be more or less normal. WiFi could disconnect and reconnect, due to a lot of reasons.

booz · 2021-09-29T10:47:00.500Z

I’m talking about random reboots - not just disconnections. How can I find out what was the reason for the last reboot?