Can't open 192.168.8.1 anymore

glitch · 2018-01-19T04:32:30.000Z

192.168.8.1/html

sciamano · 2018-01-19T15:26:22.000Z

Same result.

I’m going to reset the router and try again from scratch.

glitch · 2018-01-19T16:42:37.000Z

Sounds like a browser cache issue.

Try this: http://192.168.8.1/html/index
and this
http://192.168.8.1/cgi-bin/luci

sciamano · 2018-01-19T16:49:28.000Z

I have tried with different computers and even phones.

Even with the URLs you suggested, it does not work.

How do I reset to factory? I have tried pushing the button for 10 seconds, but nothing happened.

sciamano · 2018-01-19T17:09:10.000Z

“After 10 seconds the middle LED will flash 4 times per seconds, release your finger now and it will clear all user data and reboot.”

I have been trying this method repeatedly, but after the led starts blinking 4 times per second, and I release the button, nothing happens.

It will not do anything, doesn’t even reboot.

I think it’s a faulty unit.

sciamano · 2018-01-19T17:59:35.000Z

I think I have found the problem: I connected via ssh and I received this message:

Your JFFS2-partition seems full and overlayfs is mounted read-only.

Please try to remove files from /overlay/upper/… and rebot!

The problem now is that I can’t delete anything because it is set as read-only!

How can I do this?

sciamano · 2018-01-19T21:27:00.000Z

Ok, I solved by entering the failsafe web GUI and flashing a new firmware.

This time I have only uploaded a few ovpn files (and not the complete “library” from my VPN service), which did not saturate the memory and everything looks fine. I’ll keep testing and see what happens.

gazinbali · 2018-06-16T14:38:14.680Z

Yes… very frustrating… and some answers need a university degree just to understand.
Heres what you need to enter…

http://192.168.8.1/index.html
Hope it works for you…
Gazinbali

mikalbi · 2019-01-22T09:08:36.398Z

Hello, I want to connect Mango and when I do the search google 198.168.8.1 it puts me site inaccessible.I removed firewall and entivirus but it’s the same. I tried what you say but it does not work.

jeffsf · 2019-01-22T15:56:15.571Z

@mikalbi It seems like you’ve got a different issue than the OP. A new thread where you post what OS you’re running on your “desktop” as well as its IP addresses and routes might be a good approach.

kyson-lok · 2019-01-23T05:45:40.003Z

Why you search GooGle? You should enter 192.168.8.1 in address bar, not search filed. Make sure you have connect to the router(with LAN cable or wireless).

mikalbi · 2019-01-23T08:57:39.876Z

yes, but it does not work.

glitch · 2019-01-23T09:38:33.663Z

Because you need to put 192.168.8.1 in the address bar and not the search bar.

mikalbi · 2019-01-23T09:46:48.559Z

That’s what I did, but it does not work.

alzhao · 2019-01-23T09:50:58.011Z

post the screenshot of your browser and your network status (the page with IP address).

yostopia · 2019-01-23T19:28:54.851Z

I am having the same problem. I reset the router and now I cannot open 192.168.8.1 anymore. ??

superdave · 2022-03-06T00:15:48.506Z

I was having the same issue can not connect 192.168.8.1 in browser.

I went to my android phone, turned on wifi then in setup directed me to a browser and there I was in the routers setup!

For me, when I couldn’t connect to 192.168.8.1 you think the router doesn’t work but it does. Just not on your pc.

worldwidewebdev · 2023-01-20T12:27:57.581Z

If anyone here has updated to a newer version of OpenWrt you may see that you cannot access the GLI Admin panel. The OpenWrt website states :- Unsupported Functions:
NAND flash not supported until after 19.07.x, must be forced into booting from NOR flash You may find that going to 192.168.1.1 or 192.168.8.1 directs you to the OpenWrt Luci interface. It seems i have this problem . Getting an older version 19 firmware file is proving to be a little difficult at the moment.as of Jan 2023 and although i like the GLI Admin interface it seems for now i will be forced to stick with the full OpenWrt V22.

alzhao · 2023-01-22T02:55:43.524Z

Your link is not available anymore.

Nand is well supported in modern OpenWrt I think.

pandego · 2024-02-11T12:44:13.283Z

Cleaning the cache of my Firefox did the trick, thanks!