# Extremely Slow Speed on Slate 7

**URL:** <https://forum.gl-inet.com/t/extremely-slow-speed-on-slate-7/65627>\
**Category:** Router\
**Created:** [November 19, 2025, 10:53am UTC](https://forum.gl-inet.com/t/extremely-slow-speed-on-slate-7/65627 "2025-11-19T10:53:37Z")\
**Posts on this page:** 15\
**Page:** 2

<div class="post-metadata">

**Author:** ![will.qiu](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/w/b38774/32.png) [@will.qiu](https://forum.gl-inet.com/u/will.qiu)\
**Post date:** [December 25, 2025, 2:17am UTC](https://forum.gl-inet.com/t/extremely-slow-speed-on-slate-7/65627/23 "2025-12-25T02:17:17Z")

</div>

Thank you for sharing the test results.  
We’re pleased to see that the abnormal download speed issue has been resolved.

For the wired versus wireless performance comparison between the Slate 7 and the Beryl AX, the table appears to be truncated.  
Please share the complete table or clarify the missing data so we can better understand the difference.

From a hardware perspective, the Slate 7 should be capable of handling Tailscale traffic, as our earlier tests showed throughput above 100 Mbps -- Not the best performance, due to our limited network speed.  
To further isolate the cause, please verify whether both devices are establishing a direct connection to the overseas Linux host, or if one or both are falling back to a DERP relay. Differences in DERP usage can significantly affect throughput.

This can be verified by SSHing into the router and running the following command:

```auto
tailscale status
# OR
tailscale ping <tailscale_ip>

```

---

<div class="post-metadata">

**Author:** ![Angeleno](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/a/a87d85/32.png) [@Angeleno](https://forum.gl-inet.com/u/Angeleno)\
**Post date:** [December 25, 2025, 5:37pm UTC](https://forum.gl-inet.com/t/extremely-slow-speed-on-slate-7/65627/24 "2025-12-25T17:37:17Z")

</div>

Here are Consolidated test results.

### **Consolidated Test Results**

| **Device** | **Router** | **Connection** | **Avg. Download (Mbps)** | **Avg. Upload (Mbps)** |
| --- | --- | --- | --- | --- |
| PC | **Slate 7** | Ethernet (LAN) | 34.74 | 21.33 |
| PC | **Slate 7** | Wi-Fi | **43.06** | 20.32 |
| iPhone 15 PM | **Slate 7** | Wi-Fi | 44.03 | 22.57 |
| PC | Beryl AX | Ethernet (LAN) | 37.08 | 23.46 |
| PC | Beryl AX | Wi-Fi | 40.38 | 25.10 |
| iPhone 15 PM | **Beryl AX** | Wi-Fi | **43.13** | **39.80** |

---

<div class="post-metadata">

**Author:** ![will.qiu](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/w/b38774/32.png) [@will.qiu](https://forum.gl-inet.com/u/will.qiu)\
**Post date:** [December 26, 2025, 2:44am UTC](https://forum.gl-inet.com/t/extremely-slow-speed-on-slate-7/65627/25 "2025-12-26T02:44:11Z")

</div>

These numbers look to be within normal test variance, as the PC’s results appear consistent across both devices.

To narrow it down on the Tailscale side:

- Please check whether the traffic is **Direct** or **DERP/Relay** for the session (a relay path can significantly reduce throughput, especially to overseas exit nodes).
- If possible, please repeat the test using a **nearby exit node** (same country/region). If speeds improve, it strongly points to latency/route/DERP effects rather than the router itself.

---

<div class="post-metadata">

**Author:** ![Scalabis](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/s/6de8d8/32.png) [@Scalabis](https://forum.gl-inet.com/u/Scalabis)\
**Post date:** [December 29, 2025, 3:12pm UTC](https://forum.gl-inet.com/t/extremely-slow-speed-on-slate-7/65627/26 "2025-12-29T15:12:00Z")

</div>

Hi!

Back from holydays.

My tests were not done via WiFi, but with a connected ethernet cable.

So my tests are consistent with a direct cable connection, where the slow speeds remain as a problem.

I will try soon the WiFi option, and report here.

Regards

---

<div class="post-metadata">

**Author:** ![will.qiu](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/w/b38774/32.png) [@will.qiu](https://forum.gl-inet.com/u/will.qiu)\
**Post date:** [December 30, 2025, 7:30am UTC](https://forum.gl-inet.com/t/extremely-slow-speed-on-slate-7/65627/27 "2025-12-30T07:30:45Z")

</div>

> [@Scalabis](#):
>
> My tests were not done via WiFi, but with a connected ethernet cable.

Thank you for the clarification.

Our internal testing was conducted based on your earlier feedback, with both WAN and LAN connected via Ethernet, so Wi-Fi should not be a limiting factor here.  
_Angeleno's_ tests also confirmed that wireless connections over WAN and LAN are no problem as well.

Could you please test again using the steps below?

1. Configure the appropriate Tailscale mode on the Slate 7 with wired WAN connected.
2. SSH into the router and run the commands.
3. Confirm the commands execute successfully.
4. Run the speed test afterward, without rebooting.

---

<div class="post-metadata">

**Author:** ![Scalabis](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/s/6de8d8/32.png) [@Scalabis](https://forum.gl-inet.com/u/Scalabis)\
**Post date:** [December 31, 2025, 2:37pm UTC](https://forum.gl-inet.com/t/extremely-slow-speed-on-slate-7/65627/28 "2025-12-31T14:37:03Z")

</div>

Hi again.

Tested with your “temporary fix”

The speeds, with ethernet and/or wifi were allways around 13Mb/s Down and 13Mb/s Up.

These tests were made after a factory reset and only as a tailscale custom exit node to a Beryl.

This may be a small improvement, but replacing the Slate 7 with a Beryl, without any other modification, gets 120Mb/s Down and 60Mb/s Up.

It is perhaps better to forget the Slate 7 and stuff it away, until GL-Inet has a decent working firmware for it.

The current performance is absolutely unnaceptable.

---

<div class="post-metadata">

**Author:** ![will.qiu](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/w/b38774/32.png) [@will.qiu](https://forum.gl-inet.com/u/will.qiu)\
**Post date:** [January 4, 2026, 2:06am UTC](https://forum.gl-inet.com/t/extremely-slow-speed-on-slate-7/65627/29 "2026-01-04T02:06:37Z")

</div>

> [@Scalabis](#):
>
> These tests were made after a factory reset and only as a tailscale custom exit node to a Beryl.

Have you checked which mode Tailscale is running in—direct connection or DERP relay?

> [@will.qiu](#):
>
> This can be verified by SSHing into the router and running the following command:
> 
> ```auto
> tailscale status
> # OR
> tailscale ping <tailscale_ip>
> 
> ```

As we mentioned earlier, in our local tests, the Slate 7 achieved up to 170 Mbps DL / 100 Mbps UL without issues.

> [@will.qiu](#):
>
> ![image](https://forum-static.gl-inet.com/original/3X/8/e/8eff1d3a25df4dd7b3b194c256bc30b0b82710e9.png)
> 
> image902×480 34.8 KB

---

<div class="post-metadata">

**Author:** ![Scalabis](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/s/6de8d8/32.png) [@Scalabis](https://forum.gl-inet.com/u/Scalabis)\
**Post date:** [January 4, 2026, 9:08am UTC](https://forum.gl-inet.com/t/extremely-slow-speed-on-slate-7/65627/30 "2026-01-04T09:08:14Z")

</div>

Hi!

Yes it was a direct connection.

Exactly the same environment where immediately after I did the same with a Beryl AX, with speeds of 120Mb/s down and 60Mb/s up.

As you wrote, you will include the solution of all these matters in a new firmware release.

I eagerly expect for it.

Regards.

---

<div class="post-metadata">

**Author:** ![will.qiu](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/w/b38774/32.png) [@will.qiu](https://forum.gl-inet.com/u/will.qiu)\
**Post date:** [January 5, 2026, 9:47am UTC](https://forum.gl-inet.com/t/extremely-slow-speed-on-slate-7/65627/31 "2026-01-05T09:47:41Z")

</div>

We may not have been clear earlier.  
Previously, we only reproduced the issue where Tailscale download speeds were extremely low, approaching zero.  
We have already verified the fix using the commands provided earlier.

If Tailscale speeds remain low after executing those commands, it may indicate other issues.  
Could you share your device with us via GoodCloud following this tutorial so we can remotely investigate?  
[Technical Support via GoodCloud - GL.iNet Router Docs 4](https://docs.gl-inet.com/router/en/4/tutorials/technical_support_via_goodcloud/)  
Please send us the MAC address of devices and WebUI Password so that we can access remotely.

 ![image](https://forum-static.gl-inet.com/original/3X/1/0/10705d4a12191adc9fba880b69bfea7853d44efe.png)

---

<div class="post-metadata">

**Author:** ![cidle](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/c/d26b3c/32.png) [@cidle](https://forum.gl-inet.com/u/cidle)\
**Post date:** [January 6, 2026, 4:13am UTC](https://forum.gl-inet.com/t/extremely-slow-speed-on-slate-7/65627/32 "2026-01-06T04:13:48Z")

</div>

FWIW, I don’t have any speed issues on my slate 7 + tailscale

---

<div class="post-metadata">

**Author:** ![vsuperkei](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/v/f0a364/32.png) [@vsuperkei](https://forum.gl-inet.com/u/vsuperkei)\
**Post date:** [January 12, 2026, 12:51pm UTC](https://forum.gl-inet.com/t/extremely-slow-speed-on-slate-7/65627/33 "2026-01-12T12:51:25Z")

</div>

Hi there, i can confirm “ethtool -K eth0 tso off” fix the slowness issue I had. thanks.

However, i added into /etc/rc.local and reboot, it does not work for some reason, atm i need to ssh and execute this command manually every time after reboot.

---

<div class="post-metadata">

**Author:** ![will.qiu](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/w/b38774/32.png) [@will.qiu](https://forum.gl-inet.com/u/will.qiu)\
**Post date:** [January 13, 2026, 3:15am UTC](https://forum.gl-inet.com/t/extremely-slow-speed-on-slate-7/65627/34 "2026-01-13T03:15:17Z")

</div>

Thank you for sharing your test results.

> [@vsuperkei](#):
>
> However, i added into /etc/rc.local and reboot, it does not work for some reason, atm i need to ssh and execute this command manually every time after reboot.

It is quite strange, as our local testing shows that it should be able to configure itself automatically after a reboot.  
Could you please double-check if you added the commands **before** the `exit 0` line in the `/etc/rc.local` file?

 ![image](https://forum-static.gl-inet.com/original/3X/4/a/4af1e5118d27eca28de7966eca83078d81d5962f.png)

---

<div class="post-metadata">

**Author:** ![will.qiu](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/w/b38774/32.png) [@will.qiu](https://forum.gl-inet.com/u/will.qiu)\
**Post date:** [January 13, 2026, 4:04am UTC](https://forum.gl-inet.com/t/extremely-slow-speed-on-slate-7/65627/36 "2026-01-13T04:04:21Z")

</div>

It seems there are other applications modifying this configurations.

Perhaps you could try adding it in the `/usr/bin/gl_tailscale` startup script like this.

 ![image](https://forum-static.gl-inet.com/original/3X/4/1/410ad2914fb14505d6901adf0eca591195b480ac.png)

---

<div class="post-metadata">

**Author:** ![vsuperkei](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/v/f0a364/32.png) [@vsuperkei](https://forum.gl-inet.com/u/vsuperkei)\
**Post date:** [January 13, 2026, 4:37am UTC](https://forum.gl-inet.com/t/extremely-slow-speed-on-slate-7/65627/37 "2026-01-13T04:37:30Z")

</div>

this one (/usr/bin/gl\_tailscale) works now . thanks a lot 🙂

---

<div class="post-metadata">

**Author:** ![system](https://forum-static.gl-inet.com/original/3X/7/7/77e28f6cb342ac4bd641bd9a6254595d61b2812a.png) [@system](https://forum.gl-inet.com/u/system)\
**Post date:** [April 13, 2026, 4:38am UTC](https://forum.gl-inet.com/t/extremely-slow-speed-on-slate-7/65627/38 "2026-04-13T04:38:07Z")

</div>

This topic was automatically closed 90 days after the last reply. New replies are no longer allowed.

[Previous page](https://forum.gl-inet.com/t/extremely-slow-speed-on-slate-7/65627.md?page=1)
