Flint GL-AX1800 - 2 problems + upgrade on version 4.2.0 snapshot impossible

cynik · 2023-01-19T08:41:23.089Z

Thanks.

I will try it.

cynik · 2023-01-19T08:44:22.532Z

I will try
beta version

cynik · 2023-01-19T08:47:34.684Z

Can not…
I tried beta version - error
I tried snapshot - error

image928×528 10.7 KB

alzhao · 2023-01-19T08:51:46.707Z

I cannot see what file you tried from the screenshot.

You should use the firmware from GL.iNet download center

Use the .tar file

cynik · 2023-01-19T08:53:25.600Z

I used same, from same url
4.2.0 snapshot
tar

alzhao · 2023-01-19T08:54:55.683Z

You screenshot should at least contains the hash. Maybe you can just refresh the browser and try again.

cynik · 2023-01-19T08:56:51.633Z

I refreshed, no change
I also logged out and logged in, nothing
and also with another webbrowser - nothing = same error

I even tried rebooting the router - same result

K3rn3l_Ku5h · 2023-01-19T15:36:37.988Z

If you are going from 3.x to 4.x you are supposed to use Uboot and a .IMG file

docs.gl-inet.com

Upgrade GL-AX1800 to Firmware 4.x - GL.iNet Docs

Documentation for GL.iNet Productions

Don’t forget to update uboot

cynik · 2023-01-19T20:13:17.766Z

sorry, I dont know uboot
I need GUI interface

to explain:

i have MT1300, SFT1200 and AX1800
They all have the same GUI + Luci.
Uboot is something unknown to me

K3rn3l_Ku5h · 2023-01-19T20:41:49.754Z

Yes an no the Beryl MT1300 uses NOR Flash 32MB and the Opal SFT1200 uses SPI NAND Flash 128MB the Flint AX1800 uses NAND Flash 128MB they are also on different kernels. Anyway the MT1300 and SFT1200 are updated by the GUI but AX1800 Needs uboot and it even states that on the firmware upgrade page.

Also Uboot should be updated

Flint (4.x) update brings down my home internet for hours! Technical Support for Routers

That’s a uboot bug, the fixed version can be downloaded here. Upgrade uboot by the following steps: connect LAN and PC by ethernet, the PC’s ip should be 192.168.1.x push the reset button and power it on, about 10 seconds later release the button, until the wifi led stops flashing and the white led turns on. access http://192.168.1.1/uboot.html to flash uboot.

Uboot is simple if you follow the instructions.

docs.gl-inet.com

Debrick via Uboot - GL.iNet Router Docs 4

Documentation for GL.iNet Router Productions

cynik · 2023-01-19T20:49:11.065Z

thanks, I see…I read that already

does this mean that I will buy a new Flint and do not have to update it normally through the GUI or automatically?

Well then I’ll return it, I don’t want to have problems

Almahadeus · 2023-01-19T20:52:40.748Z

Just follow the instruction on the video linked in the referenced document above and you will not have any problems.

cynik · 2023-01-19T21:00:39.219Z

Ok guys…thanks so much…
I’ll try to do it over the weekend

K3rn3l_Ku5h · 2023-01-19T21:19:09.801Z

Just to be clear if you are going from 3.x to 4.x Update uboot first with the instructions from the link. You then want to reboot and check that the uboot firmware updated. Once that is done then update with the .IMG file ( I would use the Date Compiled: 2022-11-14 02:57:37 (UTC-05:00)SHA256: 6d3fcfde9f7b49aba32bce540ff698bcefc1849ae6bc8b9fc49682b123af9d56 This is a stable build 4.1.0. do a fresh install (do not keep settings) setup how you want and make a backup in LuCi of the config file and reboot. If you want to load a 4.2.0 beta or snapshot you can now do it from the GUI
Common problems with uboot are:
More then one device is connected to the wired connection of the router
You need to hold the power button/reset button before powering the router.
Use a private browser window when doing Uboot(this prevents cached pages)

cynik · 2023-01-19T22:02:33.840Z

Ok k3m3l, but
Just to clarify - if I do all this according to the instructions, will I have a normal GUI for administration?
And then what next, if another update is needed?

xize11 · 2023-01-19T22:39:43.689Z

You should see a different web page with uboot as logo, note that the end of the url must end with uboot like in the documentation because otherwise you are on the restore the firmware page, u-boot is basically your core bios where openwrt boots from.

To add: make sure before you upload anything that the image is 100% u-boot compatible and not just a firmware there might be links in the documentation or here else just ping me with a reply, because updating u-boot is usually not a standard procedure, this can hard brick ur device, so do so only when it has something broken in u-boot known in flint, you should see it as a procedure you only will do once and never hope to do it again.

ntrazivuk · 2023-01-20T00:33:28.654Z

I am also facing some issues / differences on 4.1 and 4.2 beta:

when acting as wireguard server, doesnt respond to DNS request from inside WG tunnel. (WG not working when I set DNS = 10.0.0.1 (WG server IP) in the WG client conf. This worked fine in 3.x.
cant reach the WG server inside the tunnel via https, although I enabled HTTPS Remote Access (this should be for WAN) and also allowed 443 in Network → Firewall → Open ports on router. Did the same for DNS.
this also worked fine in 3.x as far as I remember
also had some issues when tried downgrading back to 3.x - router crashed - so now I am back on 4.1 (had to use the process explained above)
maybe I am missing something?

K3rn3l_Ku5h · 2023-01-20T01:37:22.008Z

It will be 4.x GL.iNET firmware

docs.gl-inet.com

Overview - GL.iNet Docs

Documentation for GL.iNet Productions

cynik · 2023-01-21T13:43:47.098Z

Hi,

I found a fairly simple transition to version 4.0 beta: Dropbox - openwrt-ipq807x-glinet_ax1800-4.0_beta8.img - Simplify your life according to the instructions https://www.youtube.com/ watch?v=E8E5CUbK2Qo

Couldn’t I then normally upgrade from that 4.0 beta to 4.1 or 4.2? /no uboot/

thanks

cynik · 2023-01-21T18:00:03.639Z

So…

I ended up having to do it based on a video I found.
First 4.0 beta, and then I was able to upgrade to 4.1.0

BUT !!!
Wireguard server does not work in this version either.

I am very disappointed with this product.