Flint randomly reboot itself

cafebug · 2022-11-25T18:07:32.187Z

My Flint firmware is running at the latest stable “v.4.1.0 release 6”.

The Wi-Fi is configured in “Auto” in 80Mhz (channel 36 now ), nothing special.

xize11 · 2022-11-25T18:31:23.764Z

then I don’t know either why it crashes, the only thing what might comes to mind is the wifi crash on certain angles but I thought it was fixed.

maybe @alzhao can help ?

Almahadeus · 2022-11-25T20:08:11.141Z

Random reboots = Faulty hardware in my book.

motox22a · 2022-11-25T20:21:28.095Z

I would systematically one by one disconnect devices (IOT/Smartphones)…Reboot router and then check again…Often it is a device on the Network that is the cause and not the router.

K3rn3l_Ku5h · 2022-11-26T07:13:35.840Z

Got 11 days up time on mine, Firmware 4.1.0 release 6

Before I did notice if you ran echo ‘3’ clear cache command and waited 24hours it cashed becuase of no free ram

cafebug · 2022-11-27T21:31:07.707Z

Keep watching and found out it still reboots itself after 1 day and couple hous uptime the most.

Now disabled the SQM to see what will happen,

Keep watching…

cafebug · 2022-11-27T21:38:27.025Z

My Flint normally utilize around 5x% RAM the most, I don’t know if it’s full RAM issue, since it only serves as router and AP, nothing too complex.

K3rn3l_Ku5h · 2022-11-28T14:31:29.452Z

Sorry not following what was said in you last post.
So mine is running AdguardHome, wgclient, VPN MAC address policy, SQM for wguard, Netdata and this is ram:

Screenshot 2022-11-28 at 09-25-50 GL-AX1800 - Overview - LuCI2125×1114 128 KB

cafebug · 2022-12-01T07:19:55.628Z

After installing a 12cm fan beside Flint to let the air flow go through it, now my Flint stands alive for 2 days.

Conclusion: the reboot was caused by overheat issue.

(well, it used to operate well without any fan )

cafebug · 2022-12-01T12:23:33.429Z

Sorry, I am wrong, my Flint just reboot itself 30 minutes ago.

alzhao · 2022-12-07T11:02:10.407Z

Do you have crash log this time?

cafebug · 2022-12-07T13:24:17.199Z

Still no crash log this time.

alzhao · 2022-12-07T13:42:55.780Z

Maybe you can send back this unit to me to investigate.

I can send you a new one at the same time.

cafebug · 2022-12-07T15:38:16.018Z

Thanks for the good service, I am in the 3rd time testing, if the situation stays the same, I will contact you for the replacement.

sjoerger · 2023-02-14T02:18:55.860Z

Was there ever a determination on what may be causing these random reboots? I have a Flint router running firmware 4.1.0 release6 that has been randomly rebooting itself quite a bit lately. I also am unable to get any kind of crash log or kernel dump, etc.

alzhao · 2023-02-20T08:31:40.969Z

No.

If firmware upgrade does not solve, just need to get an exchange.

sjoerger · 2023-02-21T14:08:26.615Z

Firmware upgrade to what release? I believe I am running the latest stable version.

bOcy · 2023-02-21T15:51:03.166Z

you may try 4.2.0 beta 3, however my flint could stay working for 20+ days on 4.1 r6

check your cpu loads and memory usage (not flash)

K3rn3l_Ku5h · 2023-02-21T16:38:00.072Z

And on the 22nd day at the 13th hour your flint locked up and crashed right?
I will through my random 2 cents in with:
Been using 4.2.x snapshots sense December been pretty solid for my usage some have gone 7+ days without restart or issue (I consider that a good standard as good practice is to backup and restart equipment every 7-9 days)
Only time I have had a issue was if I kept settings, I normally load a config file saved and load any packages I want to try or need.
Good rule for Snapshot is Not to keep settings and start fresh then load a config file.

bOcy · 2023-02-22T06:47:40.867Z

was still going well but then i installed the 4.2 snapshots and rebooted