Flint WiFi issues

lizh · 2021-12-09T06:40:14.186Z

Thank you very much for your feedback, I will check it.

la3y · 2021-12-12T15:04:30.149Z

After 2 or more month my 2 pcs flints is delivered, but i’m very disappointed, they are both have low lvl noise, forum have threads with this issue

limbot · 2021-12-12T21:06:17.007Z

Send a message to cs@gl-inet.com and they should be ae to sort you out.

alzhao · 2021-12-13T02:57:55.248Z

Received your email and working on that.

olivier · 2022-01-03T19:05:54.049Z

Hello, since I switched to firmware 3.208, I have the same problem as with the 3.207, with the s2s vpn: I can no longer access the subnet of router b from Flint’s wifi (router a ). I can ping devices, but cannot connect. No problem from the wired network. I downgraded the fling to firmware 3.206 and everything is fine. Can you s.v.pl. correct the problem in the next firmware? Thanks and greetings.

olivier · 2022-01-03T22:05:53.878Z

I reset the 2 routers to the default values, installed firmware 3.208 and recreated the s2s tunnel, and everything works. Thanks and greetings.

3498BoyZ · 2022-01-04T19:45:50.385Z

So I did reset my Router to and have installed before latest FW… For now everything works… I will wait 3-4 days and response again…

martinderm · 2022-02-14T15:01:54.939Z

There are still huge 2,4G Wifi issues present for me, bandwidth around 1mbps even though there is perfect signal quality. Any news on that?

5G works perfectly, but there’s now coverage on the edges of my flat. So its quite a luxury problem. 2,4G IoT devices work as they should, they don’t require a lot of bandwidth probably.

alzhao · 2022-02-15T02:38:56.291Z

martinderm:

There are still huge 2,4G Wifi issues present for me, bandwidth around 1mbps even though there is perfect signal quality. Any news on that?

Do you have any details? I don’t have feedback like this.

martinderm · 2022-02-15T05:31:14.537Z

Well even after a fresh reset 2.4ghz wifi throughput is max 1-2 Mbit/s with perfect reception, upload usually worse, huge Ping also, 500ms. Apple devices mainly, will try to confirm with others

lord · 2022-05-31T10:36:40.336Z

@alzhao does Flint technically support 160 MHz channel width?

alzhao · 2022-06-01T04:01:37.387Z

NO. Flint only support 80MHz.

Pepperl · 2022-06-28T14:12:40.434Z

I had completely the same issue. I had an USB disk attached to the USB port. After removing the disk everything was back to normal. It seems like the disk sucked to much power and is affecting the router (funnily just the 2.4 GHZ Wifi).

alzhao · 2022-06-28T14:17:46.123Z

USB3.0 has great interference with 2.4G wifi. Are you read/writing to the disk while using 2.4G?

It interferes but should be usable.

Pepperl · 2022-06-28T14:30:19.908Z

No it was just attached. Did not read or write anything.

martinderm · 2022-06-28T15:23:37.439Z

I have the issues without any disk attached…

Pepperl · 2022-06-28T16:56:08.885Z

I made some tests right now. As soon as I plugin the SSD and do a reboot 2.4 GHZ WiFi is unusable. Plug out the SSD and reboot, everything is fine again. Thats very strange! I really need the SSD attached to the router. It is one of the main reasons I bought this router. I even tried the 4.0 beta firmware. Completely the same behavior.

luzzo · 2022-06-29T08:23:28.867Z

is it product flaw to put both usb 3.0 and wifi 2.4Ghz?

https://www.intel.com/content/dam/www/public/us/en/documents/white-papers/usb3-frequency-interference-paper.pdf

martinderm · 2022-06-29T08:42:58.399Z

My guess would be that it’s a power issue. There are plenty of routers without issues when using a USB Drive.

Pepperl · 2022-06-29T13:14:33.374Z

Well it really was the interference between the USB3 Controller from my SSD and the 2.4 GHZ Wifi.
I took a longer cable and placed the disk on an other spot and Wifi speed is almost back to normal.

Now I understand why most router manufacturer still are using USB2 ports for their devices.