GL-A1300 Beta Testing Discussions

cafebug · 2022-09-23T12:41:11.557Z

I think Beryl’s WiFi performance is better than Slate Plus. according to my testing.

lostdog · 2022-09-23T14:45:21.198Z

I’m guessing the Beryl will be phased out in favor of the Slate Plus. Nearly identical use and form factor but more processing power in the Slate Plus. VPN performance is much better.

My wifi use case is nearly always just a hotel room and I drop transmit power so I’m not broadcasting across a few city blocks. That being said, it’s nice when my room is somewhat close to the hotel gym and I can still connect!

lostdog · 2022-09-23T14:53:03.040Z

alzhao:

I am glad Hilton works. I though it is the same as Mariott.

Hilton and Marriott are owned by two different companies and not affiliated with one another. It’s been a while since I’ve stayed with a Marriott but last time I did, I don’t remember any issues connecting.

IHG properties on the other hand, I’ve had many struggles using their networks in the past (with gl-inet routers). I’ve got some traveling again in about a week. Not sure what hotel I’ll be staying at but I’ll have the Slate Plus with me and put it through more testing!

ywp · 2022-09-29T09:41:59.619Z

A1300 firmware v4.1.0_a1300_release 2 is out Technical Support for Routers

Release note: (long list) [image] Download here: https://github.com/gl-inet/gl-infra-builder/releases/download/v4.1.0_a1300_beta1/a1300.tar.gz

smiths · 2022-10-16T11:12:27.202Z

SSIDs missing if broadcasting on DFS channels, is this a known issue?

Using openwrt-a1300-4.1.0-1015-1665831919
I seem to have a problem with the GL.Inet detection of SSID on DFS channels.
I have a Meraki-G broadcasting JOLLYBOYZ_INT on channel 56 (it does transmit on 2.4GHz channel 11 as well)., and an AXT-1800 (on 4.0 s/w) connected to on 5G and retransmits the JOLLYBOYZ16 SSID on 5G, and the JOLLYBOYZ16_24 on 2.4GHz (so same channel numbers).

i can see and connect to JOLLYBOYZ16 on the GL-A1300 via the OpenWRT interface, but I cannot see the channel on GL-INET scan. If I connect via OpenWRT, GL-Inet does not see the connection, and I Cannot then even connect to the SSID in the OpenWRT interface.

The GL-INET sees below

image1279×1040 127 KB

I changed regulatory country on the 5GHz SSID to GB via openwrt, which changed it on the radio. Currently all SSID are disabled on the A1300.

iwinfo radio1 scan gives:
Cell 01 - Address: B4:0F:3B:2D:DC:04
ESSID: “VM994541”
Mode: Master Channel: 40
Signal: -90 dBm Quality: 20/70
Encryption: mixed WPA/WPA2 PSK (CCMP)
HT Operation:
Primary Channel: 40
Secondary Channel Offset: below
Channel Width: unknown
VHT Operation:
Channel Width: unknown
Center Frequency 1: 42
Center Frequency 2: 0

Cell 02 - Address: 8A:D3:43:F1:39:6F
ESSID: unknown
Mode: Master Channel: 40
Signal: -88 dBm Quality: 22/70
Encryption: mixed WPA/WPA2 PSK (TKIP, CCMP)
HT Operation:
Primary Channel: 40
Secondary Channel Offset: below
Channel Width: unknown
VHT Operation:
Channel Width: unknown
Center Frequency 1: 42
Center Frequency 2: 0

Cell 03 - Address: 18:58:80:28:B5:1A
ESSID: “BT-NQCWXN”
Mode: Master Channel: 44
Signal: -80 dBm Quality: 30/70
Encryption: WPA2 PSK (CCMP)
HT Operation:
Primary Channel: 44
Secondary Channel Offset: above
Channel Width: unknown
VHT Operation:
Channel Width: unknown
Center Frequency 1: 42
Center Frequency 2: 0

Cell 04 - Address: 18:58:80:81:41:BC
ESSID: “BT-NQCWXN”
Mode: Master Channel: 44
Signal: -89 dBm Quality: 21/70
Encryption: WPA2 PSK (CCMP)
HT Operation:
Primary Channel: 44
Secondary Channel Offset: above
Channel Width: unknown
VHT Operation:
Channel Width: unknown
Center Frequency 1: 42
Center Frequency 2: 0

Cell 05 - Address: 1A:58:80:28:B5:1A
ESSID: unknown
Mode: Master Channel: 44
Signal: -80 dBm Quality: 30/70
Encryption: WPA2 PSK (CCMP)
HT Operation:
Primary Channel: 44
Secondary Channel Offset: above
Channel Width: unknown
VHT Operation:
Channel Width: unknown
Center Frequency 1: 42
Center Frequency 2: 0

Cell 06 - Address: 62:58:80:81:41:BD
ESSID: “BTWi-fi”
Mode: Master Channel: 44
Signal: -89 dBm Quality: 21/70
Encryption: none
HT Operation:
Primary Channel: 44
Secondary Channel Offset: above
Channel Width: unknown
VHT Operation:
Channel Width: unknown
Center Frequency 1: 42
Center Frequency 2: 0

Cell 07 - Address: 4C:A6:4D:F6:84:26
ESSID: “JOLLYBOYZ”
Mode: Master Channel: 52
Signal: -51 dBm Quality: 59/70
Encryption: WPA2 PSK (CCMP)
HT Operation:
Primary Channel: 52
Secondary Channel Offset: above
Channel Width: unknown
VHT Operation:
Channel Width: unknown
Center Frequency 1: 58
Center Frequency 2: 0

Cell 08 - Address: E4:57:40:BA:49:47
ESSID: “Dallas”
Mode: Master Channel: 44
Signal: -90 dBm Quality: 20/70
Encryption: mixed WPA/WPA2 PSK (TKIP, CCMP)
HT Operation:
Primary Channel: 44
Secondary Channel Offset: above
Channel Width: unknown
VHT Operation:
Channel Width: unknown
Center Frequency 1: 42
Center Frequency 2: 0

Cell 09 - Address: 62:58:80:81:41:B8
ESSID: unknown
Mode: Master Channel: 44
Signal: -89 dBm Quality: 21/70
Encryption: WPA2 PSK (CCMP)
HT Operation:
Primary Channel: 44
Secondary Channel Offset: above
Channel Width: unknown
VHT Operation:
Channel Width: unknown
Center Frequency 1: 42
Center Frequency 2: 0

Cell 10 - Address: 82:0D:10:BB:B5:7F
ESSID: unknown
Mode: Master Channel: 48
Signal: -88 dBm Quality: 22/70
Encryption: mixed WPA/WPA2 PSK (TKIP, CCMP)
HT Operation:
Primary Channel: 48
Secondary Channel Offset: below
Channel Width: unknown
VHT Operation:
Channel Width: unknown
Center Frequency 1: 42
Center Frequency 2: 0

Cell 11 - Address: DE:CB:AC:B6:03:56
ESSID: unknown
Mode: Master Channel: 56
Signal: -36 dBm Quality: 70/70
Encryption: WPA2 802.1X (CCMP)
HT Operation:
Primary Channel: 56
Secondary Channel Offset: below
Channel Width: unknown
VHT Operation:
Channel Width: unknown
Center Frequency 1: 58
Center Frequency 2: 0

Cell 12 - Address: E6:CB:AC:B6:03:56
ESSID: “JOLLYBOYZ_INT”
Mode: Master Channel: 56
Signal: -36 dBm Quality: 70/70
Encryption: WPA2 PSK (CCMP)
HT Operation:
Primary Channel: 56
Secondary Channel Offset: below
Channel Width: unknown
VHT Operation:
Channel Width: unknown
Center Frequency 1: 58
Center Frequency 2: 0

Cell 13 - Address: 96:83:C4:19:93:27
ESSID: “JOLLYBOYZ16”
Mode: Master Channel: 56
Signal: -30 dBm Quality: 70/70
Encryption: WPA2 PSK (CCMP)
HT Operation:
Primary Channel: 56
Secondary Channel Offset: below
Channel Width: unknown
VHT Operation:
Channel Width: unknown
Center Frequency 1: 58
Center Frequency 2: 0

You will see only SSID in the safe Band A are appearing in the Gl.Inet interface.

Simon

smiths · 2022-10-16T12:10:50.772Z

If I manually add the network via the GL interface, /etc/config/repeater adds:
config network
option ssid ‘JOLLYBOYZ16’
option key ‘85PutneyBridge!21’
option proto ‘dhcp’
option metric ‘20’
option scan ‘1’

if I then try to connect, I see the following in the log:

Sun Oct 16 12:56:03 2022 daemon.info repeater: (/usr/sbin/repeater:1250) scan finished
Sun Oct 16 12:56:04 2022 daemon.info repeater: (/usr/sbin/repeater:719) Switching…
Sun Oct 16 12:56:04 2022 daemon.err repeater: (/usr/sbin/repeater:584) skip bss with dfs channel: JOLLYBOYZ16 96:83:C4:19:93:27 56
Sun Oct 16 12:56:04 2022 daemon.err repeater: (/usr/sbin/repeater:728) not found matched BSS for ‘JOLLYBOYZ16’
Sun Oct 16 12:56:04 2022 daemon.err repeater: (/usr/sbin/repeater:584) skip bss with dfs channel: JOLLYBOYZ16 96:83:C4:19:93:27 56
Sun Oct 16 12:56:04 2022 daemon.err repeater: (/usr/sbin/repeater:667) not found available network, re-scan in 59 seconds…

If I replace the option scan ‘1’ with an appropriate bssid entry, and reboot the router (think it is necessary) I can connect.

So the problem appears to be in the repeater service, which I thinkis one of yours!

Simon

groentjuh · 2022-10-16T19:46:50.152Z

I did notice that as well and I believe I had reported that in the testreport. I did not hear anything about it.

hansome · 2022-10-17T04:14:50.931Z

a1300 doesn’t have DFS support as of certification. so repeater manager scan won’t see DFS channels.
axt1800 has option to enable DFS:

smiths:

Currently all SSID are disabled on the A1300.

This may be caused by scanning by iwinfo and repeater manager conflict.
Try

/etc/init.d/repeater stop

Before iwinfo scan.

smiths · 2022-10-17T06:45:15.560Z

Hi Hansome,

All SSID disabled on router, is not a bug - just my poor explanation.
I turned off all the client wifi in the wireless menu option to focus on the wlan connection.

My problem is:
Router UI does not see DFS channels in GL-iNet UI.
I have to bypass the UI and use UCI or edit repeater config file to connect.

Leaving my AXT1800 on 4.0.3 for now, everything works (and this setting is not there, so I am guessing defaults on).

If this is a regulatory issue, then I do not want to waste your time playing around with it. I can think of a couple of ways I can make it work - if I have to, enough for me. I have been spoiilt by the 4.x on AX1800/AXT1800