Gl-inet router says 'Wrong Key' on wifi repeater join

LupusE · 2022-08-23T17:38:00.749Z

If I remember right this is a FW 3.212 issue and should be solved in 3.215.
I’m only on a beryl, but I would give the beta a try: GL.iNet download center

I do think they are active at the 4 development for the newer devices, right now. Let’s hope the waiting will also bring FW 4.x for the AR300 devices

sixspeed · 2022-08-23T20:31:49.011Z

So I figured I’d try upgrading to the 3.215 beta and no luck. Did notice that when you try to input the password and are waiting for the error to come back, it kicks me off the AR300M16 WiFi hotspot (and the SSID disappears briefly) so looks like its causing some kind of exception that restarts the hotspot service.

alzhao · 2022-08-26T08:23:06.793Z

One problem for connecting to Unifi networks, when Unifi enabled “band steering” it will cause the mini router failed to connect as repeater on 2.4G. 5G is fine.

curator · 2022-08-26T10:47:24.210Z

Do you know why that is?
Is it the same on other devices, such as laptops or other things?

datan · 2022-08-28T15:55:46.125Z

hi
I’m facing this issue on MUDI 3.211 and 3.215.

I cannot connect to wifi 2.4g that has no password (after a long pause it says “wrong key”). 5g works fine (without password).

[ 1291.579966] device wlan1 entered promiscuous mode
[ 1293.946159] wlan-sta: authenticate with 78:8a:20:xx:xx:xx
[ 1293.959723] wlan-sta: send auth to 78:8a:20:xx:xx:xx (try 1/3)
[ 1294.064755] wlan-sta: send auth to 78:8a:20:xx:xx:xx (try 2/3)
[ 1294.174758] wlan-sta: send auth to 78:8a:20:xx:xx:xx (try 3/3)
[ 1294.284818] wlan-sta: authentication with 78:8a:20:xx:xx:xx timed out
[ 1294.584034] wlan-sta: authenticate with 78:8a:20:xx:xx:xx
[ 1294.597983] wlan-sta: send auth to 78:8a:20:xx:xx:xx (try 1/3)
[ 1294.704820] wlan-sta: send auth to 78:8a:20:xx:xx:xx (try 2/3)
[ 1294.814818] wlan-sta: send auth to 78:8a:20:xx:xx:xx (try 3/3)
[ 1294.924787] wlan-sta: authentication with 78:8a:20:xx:xx:xx timed out
[ 1296.115813] wlan-sta: authenticate with 78:8a:20:xx:xx:xx
[ 1296.129589] wlan-sta: send auth to 78:8a:20:xx:xx:xx (try 1/3)
[ 1296.234766] wlan-sta: send auth to 78:8a:20:xx:xx:xx (try 2/3)
[ 1296.344757] wlan-sta: send auth to 78:8a:20:xx:xx:xx (try 3/3)
[ 1296.454782] wlan-sta: authentication with 78:8a:20:xx:xx:xx timed out

alzhao · 2022-08-29T10:08:36.195Z

datan:

[ 1291.579966] device wlan1 entered promiscuous mode
[ 1293.946159] wlan-sta: authenticate with 78:8a:20:xx:xx:xx
[ 1293.959723] wlan-sta: send auth to 78:8a:20:xx:xx:xx (try 1/3)
[ 1294.064755] wlan-sta: send auth to 78:8a:20:xx:xx:xx (try 2/3)
[ 1294.174758] wlan-sta: send auth to 78:8a:20:xx:xx:xx (try 3/3)
[ 1294.284818] wlan-sta: authentication with 78:8a:20:xx:xx:xx timed out

I am very sure that this is caused by the “band steering” setting in the Unify network. It just stop reponding to your request on 2.4G, thus forcing you to connect 5G.

We will do a research how to solve such problems.

datan · 2022-08-29T10:22:55.486Z

thank you. why does it only affect these travel routers? other devices can connect well.

alzhao · 2022-08-29T10:27:14.767Z

datan:

other devices can connect well

What other devices? phones? They have both 2.4G and 5G, right?

The router can also connect via 5G as you said.

datan · 2022-08-29T10:31:01.047Z

laptops, ipad, phone devices. right now my phone is connected by 2.4G (I checked network connection).

sometimes the 5G signal is out of range and Mudi can only detect 2.4G, which it is unable to connect to.

datan · 2022-08-29T10:55:55.890Z

here’s the network properties from Windows 10.

SSID: ABCDEF
Protocol: Wi-Fi 4 (802.11n)
Security type: Open
Network band: 2.4 GHz
Network channel: 11
Link speed (Receive/Transmit): 144/144 (Mbps)
Link-local IPv6 address:
IPv4 address: 192.168.15.42
IPv4 DNS servers: 192.168.15.1
Manufacturer: Qualcomm Atheros Communications Inc.
Description: Qualcomm Atheros QCA61x4A Wireless Network Adapter #2
Driver version: 12.0.0.722
Physical address (MAC): B4-A9-FC-xx-xx-xx

alzhao · 2022-08-29T11:02:44.359Z

OK. Thanks for the info. Let me check how I can set up and do some packete capturing

wcs2228 · 2022-08-29T16:38:37.327Z

Another possibility for not connecting to 2.4GHz wifi is that Protected Management Frames (PMF) may be enabled on the wifi access point.

I have a Unifi AP with Band Steering disabled and had problems connecting an old 2.4GHz-only travel router (not OpenWRT). I traced the problem to the PMF Required setting on the Unifi AP, but the old router does not have PMF support and PMF is mandatory for WPA3. Even for WPA2/WPA Mixed, the setting can only be PMF Optional, so I eventually had to turn off WPA3 and only have WPA2 with PMF Disabled on 2.4GHz, but not 5GHz.

Maybe the GL.iNet router has PMF support that can be enabled.

I do not work for and I do not have formal association with GL.iNet

datan · 2022-08-30T07:08:59.357Z

hi alzhao I sent you some attachments through the support email. Let me know if you received.

alzhao · 2022-08-30T07:20:36.959Z

Thanks. I received this log.

dray1989 · 2022-11-28T17:35:20.742Z

@alzhao I am having the same “Wrong Key” problem. It was working fine connecting wirelessly via repeater to my home wifi. but yesterday it stopped working. It stopped working the day before because of internet issues but I was able to reconnect MT1300 to the wifi again. I left the house, came back later that day. The wifi was working but the mt1300 internet wasn’t working. I went into the admin panel, tried to reconnect to the wifi, it wouldn’t do it. I reset the device (short and long), updated the firmware to the latest version 3.215, and it still says, “Wrong Key” when I try to connect to the wifi. I brought it to my friend’s house, connected the mt1300 to her router via ethernet. The internet worked. I tried to connect to the wifi via repeater with it connected to the router via ethernet and without it connected to the router via ethernet. It didn’t work. So, this isn’t just my internet, it is happening with other wifi connections too. I can’t connect the MT1300 to my home router because my roommate is a jerk. I need help! It has to be connected wirelessly and I need the VPN on the MT1300 for work. I can’t just connect regular.

dray1989 · 2022-11-28T17:51:41.039Z

@alzhao here is the log.

Screen Shot 2022-11-28 at 12.51.10 PM937×698 62.4 KB

alzhao · 2022-11-29T01:38:39.582Z

Can you send me the full log (via DM or via email: support at glinet.biz attn Alfie ) after wrong key? The screenshot didn’t have enough info.

Have you tried 4.1 firmware?

dray1989 · 2022-11-29T01:43:28.717Z

I haven’t tried that firmware. I’ll send the email soon. Thank you!

dray1989 · 2022-11-29T04:45:39.484Z

@alzhao I upgraded to 4.1 beta and it works! Thank you so much for the suggestion! If possible, I would still like your thoughts on why the official release of 3.215 stopped working so suddenly.

alzhao · 2022-11-29T07:19:57.891Z

dray1989:

I upgraded to 4.1 beta and it works! Thank you so much for the suggestion! If possible, I would still like your thoughts on why the official release of 3.215 stopped working so suddenly.

I checked your logs. The router get disconnected immediatelly after connected. The reason is not known.

4.x is more compatible because it is open source wifi driver.