GL-MiFi info?!

guest · 2016-02-04T21:13:33.000Z

Okay… I managed to get a telnet connection by holding the power & reset button for some time after powering up again!

Did a “reset” or something called like that with telnet.

Fingers crossed… rebooting now.

guest · 2016-02-04T21:15:28.000Z

Update… Rebooted again and got the uboot WebUI.
Flashed openwrt-mifi-20160120.bin, and am now back up again!

So… All okay for now
Pffffffff…

guest · 2016-02-04T21:43:36.000Z

Tried as suggested in the Mifi instructions from alzhao, but still no 3G

Are you having any luck Jan-Willem?

jw1 · 2016-02-04T22:19:49.000Z

Not yet I’m sorry to say. Also had to drop it for a while because of time constraints.

As mentioned before I am still stuck at the PPP negotiation phase.

I will try to find some time over the weekend to dig deeper and also document the QMI option which could work for us as an alternative. It uses the kmod-usb-net-qmi-wwan kernel module which takes care of setting up the connection eleminating the use of the fiddly PPP dial scripts.

guest · 2016-02-04T23:04:24.000Z

No problem…

I’ve got everything setup nicely (3D printed a nice cover. Build a nice cloverleaf wifi antenna).
All I need now is to get the MiFi to work and I’m done with the proto-type.

If this is not going to work, than I will move back to the 150 with USB 3G stick.

jw1 · 2016-02-05T01:00:24.000Z

Nice!

Do share a pic when you get it going!

alzhao · 2016-02-05T13:09:48.000Z

@Guest, I have just read this long post again to understand the problem.

I don’t know how you tried. But let’s do this once again using same configuration.

First, use ttyUSB2 to send command and use ttyUSB3 for network "option device ‘/dev/ttyUSB3’, I bet your apn setting is correct.

Second, unplug power, then plug power again. If you tried to connect before, a software reboot may not correct the problem.

Third, after the system boot, let’s check network and try AT command. You can just try “comgt” simply to check if you have any luck. Then you can try the AT command one by one from the quick guide to get the output. Next pls post your log.

guest · 2016-02-05T18:10:21.000Z

Hi alzhao,

I will try later and report back with logs.

guest · 2016-02-05T22:49:13.000Z

Please note that the NANO sim is working fine in another phone, and USB 3G stick.
The NANO sim is also an original one (ie: not trimmed)

1st tested: /dev/tty/USB2, and rebooted

root@domino:~# comgt Trying list of devices ***SIM ERROR*** Check device port configuration. Check SIM is inserted Test SIM in a mobile phone? root@domino:~#

Changed to: /dev/tty/USB3, and rebooted

root@domino:~# comgt Trying list of devices ***SIM ERROR*** Check device port configuration. Check SIM is inserted Test SIM in a mobile phone? root@domino:~#

guest · 2016-02-07T06:09:38.000Z

For your information: I’ve ordered a new MiFi Engineering Board (without the modem)
I hope that the SIM card holder is okay on this new one :-/

alzhao · 2016-02-12T12:14:03.000Z

@Guest, from what I understand this should not be the problem of SIM connection.

I have tried two SIM cards here, one 3G and one 4G and I tried both EC20 and UC20.

The 3G SIM card works good with EC20 and UC20.

But the 4G SIM card only works with EC20 (or UC20) in openwrt 1407 in umts mode.

I haven’t sort of the problem but this should be a driver problem. I will buy more SIM card and try. Next week engineers will come back from New Year holiday and hopefully I will get more docs.

guest · 2016-02-12T17:17:58.000Z

@alzhao,

Thank you for your reply.
The card I’m testing with is a 3G sim card.

guest · 2016-02-18T23:32:38.000Z

Yahoooooo…

Received the new MiFI today, and installed the “old” radio on it.
Update the MiFi with: openwrt-mifi-20160120.bin, added the needed data for my 3G provider and set it to use COM3

Guess what…

root@domino:~# comgt Trying list of devices SIM ready Waiting for Registration..(120 sec max) Registered on Home network: "KPN",6 Signal Quality: 10,99 root@domino:~#

And yes.... Internet is also working over 3G :-)

I guess that the 1st MiFi I received did have a problem with the SIM card reader.

jw1 · 2016-02-19T03:05:46.000Z

Great news!

I guess I will give it a shot as well with that firmware as soon as I have a moment.

guest · 2016-02-19T06:37:41.000Z

I’ve had that firmware on my other MiFi from day 1, but never got it to work… We know why now :-/

By the way… This webcam ( 404 Page not found - GL.iNet ) does also work great on the MiFi

alzhao · 2016-02-19T11:35:04.000Z

@guest, great to hear that.

Check your old MiFi board to see if you could save it.

danarnell · 2016-02-22T05:42:35.000Z

mine arrived actually pretty fast

got a few days to play with it

shame there are no mounting holes for the board though (only the pcie slot)

guest · 2016-02-22T05:59:03.000Z

You can extend the 2 screws from the radio to hold it in a box.

I’ve printed (3d) a small box for mine to fit inside a dome, and am using extended screws to hold it in place.

PS: I don’t mind having a look at your modified quick start guide.

danarnell · 2016-02-23T02:00:36.000Z

i cant say ive really changed that much,

added section on AT & dataports for various modems
added default wifi password
corrected some spelling/grammar mistakes (and probably added a few too)

I hope the guys at GLI dont have an issue with me posting this

https://mega.nz/#!PUkkhBSL!_qMOQZyR_utPx9OU8k5Z-CuAfWhhP4mV3uPX5FG_8sQ

guest · 2016-02-23T04:02:21.000Z

Not really needed anymore, but it’s looking good!

Thank you.