# GL-MT3000 stops working when connecting to Tailscale Exit Node **URL:** \ **Category:** Router\ **Created:** [October 12, 2023, 5:15pm UTC](https://forum.gl-inet.com/t/gl-mt3000-stops-working-when-connecting-to-tailscale-exit-node/34146 "2023-10-12T17:15:16Z")\ **Posts on this page:** 7\ **Page:** 3
**Author:** ![mikeuk](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/m/258eb7/32.png) [@mikeuk](https://forum.gl-inet.com/u/mikeuk)\ **Post date:** [September 21, 2024, 6:34pm UTC](https://forum.gl-inet.com/t/gl-mt3000-stops-working-when-connecting-to-tailscale-exit-node/34146/41 "2024-09-21T18:34:13Z")
Thank you, this fixed it for me with my new Beryl AX running 4.6.4 - is the gl.inet team aware of this issue? There are so many broken things out-of-the-box with this device I'm honestly thinking of returning it. ---
**Author:** ![Gravity8602](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/g/76d3ee/32.png) [@Gravity8602](https://forum.gl-inet.com/u/Gravity8602)\ **Post date:** [October 3, 2024, 10:00am UTC](https://forum.gl-inet.com/t/gl-mt3000-stops-working-when-connecting-to-tailscale-exit-node/34146/42 "2024-10-03T10:00:30Z")
I had a similar issue and was able to solve it in a few different ways: > [@Beryl AX (GL-MT3000) using a tailscale exit node](https://forum.gl-inet.com/t/beryl-ax-gl-mt3000-using-a-tailscale-exit-node/47744/4): > > Luci configuration safe. Thank you that is good to know. You can install the TS client in the phone/computer, etc, to verify whether the exit node is available. This works fine, I have been using this exist node with my phone and laptop for a while. If available, please reset router and enable the TS in the GL admin panel, rebind it (let the TS re-create the route table), and in general there are not require configuring anything in the LuCI and SSH. Just to clarify the ssh config I di… ---
**Author:** ![op123](https://forum-assets.gl-inet.com/user_avatar/forum.gl-inet.com/op123/32/24188_2.png) [@op123](https://forum.gl-inet.com/u/op123)\ **Post date:** [March 26, 2025, 10:45am UTC](https://forum.gl-inet.com/t/gl-mt3000-stops-working-when-connecting-to-tailscale-exit-node/34146/44 "2025-03-26T10:45:42Z")
I am not able to access the internet after the LUCI changes ---
**Author:** ![qatar2022](https://forum-assets.gl-inet.com/user_avatar/forum.gl-inet.com/qatar2022/32/15798_2.png) [@qatar2022](https://forum.gl-inet.com/u/qatar2022)\ **Post date:** [April 14, 2025, 1:37pm UTC](https://forum.gl-inet.com/t/gl-mt3000-stops-working-when-connecting-to-tailscale-exit-node/34146/45 "2025-04-14T13:37:41Z")
thank you @Cfm765 that's also works for me ---
**Author:** ![sammutd88](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/s/b3f665/32.png) [@sammutd88](https://forum.gl-inet.com/u/sammutd88)\ **Post date:** [June 2, 2025, 11:39pm UTC](https://forum.gl-inet.com/t/gl-mt3000-stops-working-when-connecting-to-tailscale-exit-node/34146/46 "2025-06-02T23:39:32Z")
This is magic right here and has solved my issue. Thanks a lot. Clearly wasn’t anything in my tailscale config at either end. ---
**Author:** ![link2rn](https://forum-assets.gl-inet.com/user_avatar/forum.gl-inet.com/link2rn/32/25799_2.png) [@link2rn](https://forum.gl-inet.com/u/link2rn)\ **Post date:** [June 10, 2025, 1:37am UTC](https://forum.gl-inet.com/t/gl-mt3000-stops-working-when-connecting-to-tailscale-exit-node/34146/47 "2025-06-10T01:37:17Z")
Kudos to you @Cfm765. Idk why Gl-inet is so dumb to make this feature feasible if they are adding as plug-in. Hats off! I might experience slow network bandwidth but it works! ---
**Author:** ![bruce](https://forum-assets.gl-inet.com/user_avatar/forum.gl-inet.com/bruce/32/35649_2.png) [@bruce](https://forum.gl-inet.com/u/bruce)\ **Post date:** [November 5, 2025, 10:12am UTC](https://forum.gl-inet.com/t/gl-mt3000-stops-working-when-connecting-to-tailscale-exit-node/34146/48 "2025-11-05T10:12:14Z")
[Previous page](https://forum.gl-inet.com/t/gl-mt3000-stops-working-when-connecting-to-tailscale-exit-node/34146.md?page=2)