Gl-mt3000 v4.1.2 beta : quectel eg25-g with external USB enclosure

bOcy · 2022-12-28T10:12:50.868Z

bOcy · 2022-12-28T10:15:17.147Z

going to update firmware to 4.2 beta1

edit: bricked twice trying to go to 4.2, flashed back to 4.1.2 and taking a break until the next workable 4.2 build

bOcy · 2022-12-29T17:04:56.532Z

mt3000 4.2 beta 2 : still need to modify qmi.sh file for modem to ‘auto setup’, but modem stays alive after 2 hours, which is improvement from 4.1

jddebug · 2023-07-26T14:29:11.498Z

Did you ever get this working reliably? I also have the same setup and am having the same problems. I can get it to work using Protocol 3G port ttyUSB3 and service LTE in manual setup but its very unreliable. Stays connected but internet doesn’t work right most of the time.

jddebug · 2023-07-26T21:44:19.183Z

Possible to get step by step instructions on this? I am having the same problem but do not know the steps to take to upgrade module firmware. I found my qmi.sh was somewhat different than your screenshot too.

bOcy · 2023-07-27T07:11:25.286Z

Check if your isp controls hotspot type connection, research about changing TTL if you haven’t done so

alzhao · 2023-07-31T10:43:38.867Z

Pls do:

Upgrade router firmware to latest
Post the modem status page which display the modem model.

jddebug · 2023-08-25T23:45:50.077Z

Upgraded to latest firmware.

What do you mean by Modem Status Page? Is it this you want?
Modem Name EG25GGBR07A08M2G

On the previous firmware I was able to edit -/lib/netifd/proto/qmi.sh and get everything working. Unfortunately this newest firmware is completely different /lib/netifd/proto/qmi.sh and I am not sure what to edit to get it working. the few things I have tried have not worked.

This is what I did to get it working with previous firmware. Just posting the section I edited. Look for the ----------------> pointing to the line I changed.

                   #External modem module                                                                                                                                   
                    name_file=$(cat /proc/gl-hw-info/usb-port | grep ",")                                                                                                    
                    if [ -z "$name_file" ]; then                                                                                                                             
                            name_file=$(cat /proc/gl-hw-info/usb-port)                                                                                                       
                    else                                                                                                                           
                            name_file=$(cat /proc/gl-hw-info/usb-port | sed 's/,/ /g')                                                             
                    fi                                                                                                                                                       
                                                                                                                                                   
                    for iter in $name_file; do                                                                                                                               
                            name=$(gl_modem -B $iter AT ATI |grep Revision)                                                                                                  
                            if [ -n "$name" ];then                                                                                                                           
                                    name=$(gl_modem -B $iter AT ATI |grep Revision |awk '{print $2}')                                              
                                    support_raw=`echo ${name}| grep -E "EG25|EC25|EC20|EP06|EM060K|EM160R|RM520N"`                                                           
                                                                                                                                                                             
                                    if [ -z "$support_raw" ]; then                                                                                                           
                                            echo "N" > /sys/class/net/$ifname/qmi/raw_ip                                                           
                                    else

--------------> echo “N” > /sys/class/net/$ifname/qmi/raw_ip
fi
fi
done

            else                                                                                                                                   
                    echo "Device only supports raw-ip mode but is missing this required driver attribute: /sys/class/net/$ifname/qmi/raw_ip"       
            fi                                                                                                                                                               
    fi                                                                                                                                                                       
                                                                                                                                                   
    uqmi -s -d "$device" --sync > /dev/null 2>&1                                                                                                                             
                                                                                                                                                                             
    [ -n "$modes" ] && uqmi -s -d "$device" --set-network-modes "$modes" > /dev/null 2>&1                                                                                    
                                                                                                                                                                             
    echo "Starting network $interface"

/lib/netifd/proto/qmi.sh 224/474 47%

lizh · 2023-08-26T09:41:41.910Z

Hi jddebug:

If modified to echo “Y” > /sys/class/net/$ifname/qmi/raw_ip, Whether it works properly?

bOcy · 2023-08-26T09:59:20.745Z

Please note I did update my quectel modem firmware with glinet help, if your modem hasn’t update for a few years, maybe you need to update it

jddebug · 2023-08-26T13:25:28.824Z

Yes, when I made that modification on the previous firmware it fixed everything and I was able to connect. I can not find correct change to fix the newest firmware so I can’t connect.

jddebug · 2023-08-26T13:26:16.766Z

I’d like to try that. Did they send you instructions or did they do it for you? Mine is the EG25-G.

bOcy · 2023-08-26T16:09:01.634Z

Fired up my mt3000 that has 4.4.5 days ago, yeap external modem eg-25g can’t establish connection, going back to 4.2.3

bOcy · 2023-08-26T16:11:10.170Z

Gl-mt3000 v4.1.2 beta : quectel eg25-g with external USB enclosure Technical Support for Routers

You can use this command （gl_modem -B 1-1 AT AT+QGMR）to check the firmware version of the modem [image]

Check earlier in the post, it’s a process of checking your modem serial and giving to them so that they can ‘make’ the firmware for you

jddebug · 2023-08-26T16:35:28.683Z

Gl-mt3000 v4.1.2 beta : quectel eg25-g with external USB enclosure:

gl_modem -B 1-1 AT AT+QGMR

I got this:

AT+QGMR

EG25GGBR07A08M2G_01.001.01.001

lizh · 2023-08-28T02:02:15.521Z

I will check it. It may take some time.

bOcy · 2023-08-29T04:05:02.288Z

image781×494 12.5 KB

for 4.4.5 i modified here, then initially the router couldnt detect the modem even after one reboot

i switched to another usb modem that uses tethering then switch back to the external modem it then able to establish data connection (and set ttl works)

how long it can stay online, will monitor

update modem not so stable in this firmware, it goes offline randomly and becomes undetected by mt3000, maybe theres more configuration required but its out of my capability

jddebug · 2023-08-29T15:20:25.062Z

Thanks for the reply and taking a stab at it. This is difficult not having my cell modem anymore. Is disappointing they removed signal strength info and set the default USB port to USB0 with this firmware so making AT commands is a pain. Have to select USB3 every time you issue a command and can’t easily set your antenna due to no cell signal strength info.

jddebug · 2023-09-12T01:13:09.018Z

GL-iNET. Can you help us out with this? The previous firmware we were able to get things working after editing the qmi.sh file but now that file has very different content and we can’t use our modems anymore.

lizh · 2023-09-13T11:04:14.875Z

jddebug:

Have to select USB3 every time you issue a command and can’t easily set your antenna due to no cell signal strength info.

This issue will be corrected as soon as possible.

There are some issues with the qmi driver, which are being debug.