# GL-MT6000 Flint 2 Access Point mode Guest/IoT network not giving IP

**URL:** <https://forum.gl-inet.com/t/gl-mt6000-flint-2-access-point-mode-guest-iot-network-not-giving-ip/70687>\
**Category:** Router\
**Created:** [August 20, 2026, 7:48am UTC](https://forum.gl-inet.com/t/gl-mt6000-flint-2-access-point-mode-guest-iot-network-not-giving-ip/70687 "2026-08-20T07:48:57Z")\
**Posts on this page:** 1\
**Showing post:** 4

<div class="post-metadata">

**Author:** ![charles2](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/c/9dc877/32.png) [@charles2](https://forum.gl-inet.com/u/charles2)\
**Post date:** [August 21, 2026, 7:11am UTC](https://forum.gl-inet.com/t/gl-mt6000-flint-2-access-point-mode-guest-iot-network-not-giving-ip/70687/4 "2026-08-21T07:11:03Z")

</div>

Hi,

When the Flint 2 is operating in Access Point Mode, NAT and DHCP are disabled, and the device mainly works as a Layer 2 access point/switch. Client IP addresses therefore need to be provided by the upstream router. Simply re-enabling the IoT or Guest SSID in LuCI only enables the wireless interface itself. It does not automatically restore a separate subnet or DHCP service for that network.

If you would like to keep separate IoT and Guest networks while using the Flint 2 as an AP, the upstream router needs to support VLANs and provide the gateway/DHCP service for each VLAN. The Flint 2 can then be configured as a VLAN-aware AP, with the corresponding IoT/Guest Wi-Fi interfaces mapped to their VLANs.

You can refer to the following examples:  
Flint 2 + AP Mode + upstream VLAN/DHCP

> [@Flint 2 as "dumb" VLAN (W)AP + OPNsense router](https://forum.gl-inet.com/t/flint-2-as-dumb-vlan-w-ap-opnsense-router/70569):
>
> Hi, I recently got a Flint 2 router, and I wanted to put it behind an OPNsense router to use it as a dumb WAP. Furthermore, I wanted to divide my network as follows: Step 1: Wireless access point for trusted devices and all Ethernet ports for trusted devices Step 2: Wireless access point for untrusted devices and one Ethernet port for untrusted devices Since I want my OPNsense router to manage everything, I thought I would need to use VLANs. Step 1 worked, but Step 2 failed. When trying to c…

Multiple SSIDs + VLAN configuration example

> [@Flint 3 (GL-BE9300) as AP behind pfSense: multiple SSIDs -\> VLAN + Random BSSID](https://forum.gl-inet.com/t/flint-3-gl-be9300-as-ap-behind-pfsense-multiple-ssids-vlan-random-bssid/66719/4):
>
> Hi Well, overall your requirements are feasible. However, the configuration will be quite complex, and it requires you to have sufficient knowledge of networking concepts as well as a solid understanding of LuCI/UCI. Below is a configuration example. Since the steps for Work and IoT are repetitive, only Main / Guest / IoT are used as examples here. Topology is as follows: Configuration steps: Start from a factory-default BE9300 v4.8.3 configuration Configure its WAN port as …

Thank you for your support and understanding.

---

_[View the full topic](https://forum.gl-inet.com/t/gl-mt6000-flint-2-access-point-mode-guest-iot-network-not-giving-ip/70687)._
