GL-X1200 not using Static IP

wellnw · 2020-02-24T07:56:26.764Z

@Technicavolous
It is usually up to APN to assign static IP, please set APN as follows

Technicavolous · 2020-02-24T14:07:33.527Z

Yes thank you we have done this. As stated above, APN for static IP is B2B.static. Works perfectly with 06 model, does not work with 08 model.

apn2942×383 22.3 KB

Proper IP shows in settings with 06 unit, not with 08 unit. No data passes with 08 model, data passes with 06 model, every time, every unit … (GL-MiFi, Spitz, Amrok)

static1955×422 22.8 KB

I have contacted T-Mobile to see if they can give insight from logs or what they have. Waiting response as we asked Saturday.

Seems like one should be able to see these differences in a data sheet but I have not found any doc that shows what those particular numbers represent. Your examples show '04 and '06, perhaps it is a release version?

This is big deal for us, I sold several units with Static IP and now might have to replace units. Need to fix this :[

Technicavolous · 2020-02-24T17:14:01.241Z

I just noticed that my units with “08” modems have firmware 3.027 and the units with “06” modems have 3.1 firmware.

I recall being on Goodcloud and receiving a message to upgrade the GL-MiFi and Mango to 3.1 for certain functionality. I can’t seem to make this happen on the Amarok or Spitz.

https://dl.gl-inet.com/firmware/x750/testing/
https://dl.gl-inet.com/firmware/x1200/testing/

Tonight I will try ‘testing’ firmware and report back.

Technicavolous · 2020-02-25T01:13:16.037Z

Had to revert the X1200 to 3.027 - with 3.100 I was unable to access the GL gui, only the lucy interface … I know I saw that issue somewhere but can’t find it again.

wellnw · 2020-02-25T01:19:42.714Z

@Technicavolous
I will update the test firmware of X1200 today

Technicavolous · 2020-02-25T02:15:18.160Z

COOL!!

Because I just proved 5 times I could flash 3.027 and get the initial config and all the menus just fine, but the 3.1 will never go to #internet … I can force 192.168.8.1/welcome-guide.html, it lets create password, but only can log into Luci.

wellnw · 2020-02-25T09:50:10.606Z

@Technicavolous
Hi ,
Please go to the following link to download the latest firmware test, and look forward to your feedback, thank you
https://dl.gl-inet.com/firmware/x1200/testing/

image881×321 21.6 KB

Technicavolous · 2020-02-26T04:34:24.429Z

I have updated to the firmware you referenced and the unit boots and browses into the GUI nicely.
Tomorrow I will have the static sim to test and will report back again.

Screenshot at 2020-02-25 23-37-231051×360 14.7 KB

Thank you!

Technicavolous · 2020-02-26T05:23:48.969Z

Well I have the static sim … wow it is NOT a modem problem but a firmware one for the X1200 - static IP is working with 3.012!!

Screenshot at 2020-02-26 00-10-40-21050×412 39.2 KB

Now will try with Spitz and MiFi - static sim did not work with those units on 3.0xx.

Thank you again

Technicavolous · 2020-02-26T05:42:09.514Z

@wellnw Spitz does not pull the static ip with either B2B.static or fast.t-mobile.com APN :[
Updated to current 3.1 in download section. Still no static.

It pulls a DHCP address and registers the system, but no data can pass since the IP pulled is not the one assigned to the sim.

Testing MiFi next

Technicavolous · 2020-02-26T06:35:45.754Z

@wellnw Brand new out of box GL-MiFi Only gives “Sim card not registered” … will continue testing tomorrow.

Technicavolous · 2020-02-27T13:47:13.553Z

@wellnw MiFi and Spitz still no static IP with 3.1 … 3.102 for those soon?
Please? ;]

wellnw · 2020-02-28T01:31:53.287Z

Technicavolous:

MiFi and Spitz still no static IP with 3.1 … 3.102 for those soon?

@Technicavolous
We will update to 3.102 for MiFi and Spitz today.

wellnw · 2020-02-29T01:21:17.038Z

@Technicavolous
MiFi and Spitz update to 3.103, you can try it ,thank you.

http://download.gl-inet.com/firmware/x750/snapshots/
http://download.gl-inet.com/firmware/mifi/snapshots/

Technicavolous · 2020-03-02T03:39:06.136Z

I was excited to tell you that the static IP works on both MiFi and Spitz, but I kept getting Bad Gateway error on the forum. Good to see it back up!!

I have not tested other features, since this is in ‘snapshots’ I assume it is not ready for end user release??

wellnw · 2020-03-02T04:57:29.652Z

@Technicavolous
We will release the official firmware as soon as possible, thank you for your feedback

Technicavolous · 2020-06-07T13:56:44.585Z

Hope all is well, any plan on official release? Thank you for your hard work, it is very appreciated!

alzhao · 2020-06-08T07:54:33.007Z

I think for most models we have 3.104 published already.

admon · 2024-11-02T18:28:50.207Z

A post was split to a new topic: X300B 4.x firmware - Can't use static IP SIM

admon · 2024-11-02T18:28:15.334Z