# How to get Tailscale working on the Beryl MT-1300!

**URL:** <https://forum.gl-inet.com/t/how-to-get-tailscale-working-on-the-beryl-mt-1300/31598>\
**Category:** Router\
**Created:** [July 20, 2023, 8:35am UTC](https://forum.gl-inet.com/t/how-to-get-tailscale-working-on-the-beryl-mt-1300/31598 "2023-07-20T08:35:10Z")\
**Posts on this page:** 15\
**Page:** 1

<div class="post-metadata">

**Author:** ![HarvsG](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/h/c57346/32.png) [@HarvsG](https://forum.gl-inet.com/u/HarvsG)\
**Post date:** [July 20, 2023, 8:35am UTC](https://forum.gl-inet.com/t/how-to-get-tailscale-working-on-the-beryl-mt-1300/31598/1 "2023-07-20T08:35:10Z")

</div>

I wanted to use a Tailscale mesh rather than a self-hosted hub and spoke wireguard vpn for my site to site.  
This is how I got it working on the Beryl ([after some trial and error](https://forum.gl-inet.com/t/when-can-we-expect-tailscale-suppot-on-beryl-mt1300/31151/9)), it _may_ work on some other devices.

1. Go to [https://dl.gl-inet.com/](https://dl.gl-inet.com/) and download the firmware version you **currently** have installed - if you need to restore, you might not have internet.
2. Download/Backup your config. I can’t remember if you can do it through your GUI in 3.x, otherwise you can do it in the advanced Luci GUI in `system` → `Backup/Flash Firmware`
3. Go back to [https://dl.gl-inet.com/](https://dl.gl-inet.com/) and download the latest 4.x firmware - we need the new Tailscale GUI on the OpenWRT 22 to support tailscale
4. Flash it using the GUI installer.
5. When my router came back up it wouldn’t get a DHCP address from my Modem even after a restart of both - I had to switch ports in the modem and maybe restart the modem.
6. `Applications` → `Plugins` → search `tailscale`
7. Install `gl-sdk4-tailscale`  
I. It should auto-install the other 3 search results
8. Reboot router
9. `Applications` → `Tailscale` → `Enable Tailscale`
10. ![image](https://forum-static.gl-inet.com/original/2X/3/3a25e72bde52e92dac0877b22f13a4def5c5f980.png)  
I. Im not sure how allow remote access WAN is helpful - presumably it is a stand in whilst they get `--advertise-exit-node` working - I would disable it for now.
11. You will get a link to ‘bind device’, this didn’t work for me
12. Instead SSH into the router then run `tailscale status`, the binding link should appear, copy and paste it and authenticate
13. You should see in the Tailscale admin panel that the device is now connected. You can allow any advertised routes here.

Now at this stage, whilst SSHed into the router I could ping devices on the Tailscale network and on exposed subnets, but devices on my home network, couldn’t. I.e beryl wasn’t routing the packets, pings from devices returned “Destination unreachable”. Which rather undermined the idea of site-to site. But looks as if this may not be unique to the Beryl: [Tailscale cannot reach subnets on other devices - #7 by jsr](https://forum.gl-inet.com/t/tailscale-cannot-reach-subnets-on-other-devices/27063/7)

To fix:

1. Log in to the advanced Luci GUI panel, go to `Network` → `Firewall` ( **not** `Status` → `Firewall`)
2. Edit the first row ![image](https://forum-static.gl-inet.com/original/2X/e/e9c1fafc62cec32d66599944fd6da877cf3abe00.png)
3. On the second tab add covered devices: tailscale0 ![image](https://forum-static.gl-inet.com/original/2X/b/b4d717f69d5af6964b5e669a251a90dfe2a17b8c.png)
4. Save and Save & Apply

Edit: I find that every few days the routing fix breaks (I think something refreshes the routing tables or similar) disabling and then re-enabling the tailscale fixes it.

---

<div class="post-metadata">

**Author:** ![HarvsG](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/h/c57346/32.png) [@HarvsG](https://forum.gl-inet.com/u/HarvsG)\
**Post date:** [July 20, 2023, 8:41am UTC](https://forum.gl-inet.com/t/how-to-get-tailscale-working-on-the-beryl-mt-1300/31598/2 "2023-07-20T08:41:54Z")

</div>

Solution is above - marking as solved  
@alzhao - are you interested in rolling this out?

---

<div class="post-metadata">

**Author:** ![alzhao](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/a/5f9b8f/32.png) [@alzhao](https://forum.gl-inet.com/u/alzhao)\
**Post date:** [August 10, 2023, 3:23am UTC](https://forum.gl-inet.com/t/how-to-get-tailscale-working-on-the-beryl-mt-1300/31598/3 "2023-08-10T03:23:28Z")

</div>

We may not fit Tailscale for MT1300 but for the “reach subnets” thing should be fixed (or have already been fixed).

---

<div class="post-metadata">

**Author:** ![HarvsG](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/h/c57346/32.png) [@HarvsG](https://forum.gl-inet.com/u/HarvsG)\
**Post date:** [August 17, 2023, 3:09pm UTC](https://forum.gl-inet.com/t/how-to-get-tailscale-working-on-the-beryl-mt-1300/31598/4 "2023-08-17T15:09:14Z")

</div>

> [@alzhao](#):
>
> We may not fit Tailscale for MT1300

That is sad, because it is working well, it would be a shame for you not to add a feature to a product that supports is ☹

> [@alzhao](#):
>
> the “reach subnets” thing should be fixed

Fixed in which version? I still lose routing to exposed subnets on other parts of my tailnet every 36 hours or so (I can still ping all nodes on the tailnet). Simply disabling and enabling fixes it though

---

<div class="post-metadata">

**Author:** ![HarvsG](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/h/c57346/32.png) [@HarvsG](https://forum.gl-inet.com/u/HarvsG)\
**Post date:** [August 21, 2023, 3:23pm UTC](https://forum.gl-inet.com/t/how-to-get-tailscale-working-on-the-beryl-mt-1300/31598/5 "2023-08-21T15:23:30Z")

</div>

After more testing tailscale struggles to do more than 20Mbs / 2-3MB/s throughput ☹

I upgraded manually to a more recent version of tailscale (1.44) using the packages from here: [Index of /releases/23.05.0-rc1/packages/mipsel\_24kc/packages/](https://downloads.openwrt.org/releases/23.05.0-rc1/packages/mipsel_24kc/packages/)

However I didn’t get an appreciable increase in speed.

---

<div class="post-metadata">

**Author:** ![CVO](https://forum-assets.gl-inet.com/user_avatar/forum.gl-inet.com/cvo/32/12535_2.png) [@CVO](https://forum.gl-inet.com/u/CVO)\
**Post date:** [August 31, 2023, 6:38pm UTC](https://forum.gl-inet.com/t/how-to-get-tailscale-working-on-the-beryl-mt-1300/31598/6 "2023-08-31T18:38:22Z")

</div>

Hmm, I tried this but:

- I had to install the UI package as well
- I don’t have “wgclient”
- (via SSH) I can connect to devices on remote networks (advertised as routes on other tailscale nodes) from the MT-1300 and I can ping other tailscale IPs from the MT-1300
- I can’t connect to remote devices or ping tailscale IPs from any LAN devices (eth or wifi)
- I tried adding routes for the subnets manually and pointing them at tailscale0 interface but that didn’t work.

Any ideas? I’m running the latest beta firmware (4.3.7 release 1, also tried upgrading to the 8/23 4.3.7 snapshot)

Edit: I followed the instructions here for the luci changes and it works: [Tailscale cannot reach subnets on other devices - #23 by ss4pcRFradio](https://forum.gl-inet.com/t/tailscale-cannot-reach-subnets-on-other-devices/27063/23)

---

<div class="post-metadata">

**Author:** ![danielg](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/d/f0a364/32.png) [@danielg](https://forum.gl-inet.com/u/danielg)\
**Post date:** [September 10, 2023, 8:09am UTC](https://forum.gl-inet.com/t/how-to-get-tailscale-working-on-the-beryl-mt-1300/31598/7 "2023-09-10T08:09:28Z")

</div>

Would zerotier perform any better on Beryl?

---

<div class="post-metadata">

**Author:** ![HarvsG](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/h/c57346/32.png) [@HarvsG](https://forum.gl-inet.com/u/HarvsG)\
**Post date:** [September 21, 2023, 7:04pm UTC](https://forum.gl-inet.com/t/how-to-get-tailscale-working-on-the-beryl-mt-1300/31598/8 "2023-09-21T19:04:34Z")

</div>

> [@HarvsG](#):
>
> Now at this stage, whilst SSHed into the router I could ping devices on the Tailscale network and on exposed subnets, but devices on my home network, couldn’t. I.e beryl wasn’t routing the packets, pings from devices returned “Destination unreachable”. Which rather undermined the idea of site-to site. But looks as if this may not be unique to the Beryl: [Tailscale cannot reach subnets on other devices - #7 by jsr](https://forum.gl-inet.com/t/tailscale-cannot-reach-subnets-on-other-devices/27063/7)

See the points after point 12 for how I solved routing from LAN to tailnet

---

<div class="post-metadata">

**Author:** ![adokitkat](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/a/9dc877/32.png) [@adokitkat](https://forum.gl-inet.com/u/adokitkat)\
**Post date:** [November 25, 2023, 12:43pm UTC](https://forum.gl-inet.com/t/how-to-get-tailscale-working-on-the-beryl-mt-1300/31598/9 "2023-11-25T12:43:06Z")

</div>

Hi,

did you get custom exit node to work? In my case it just won’t work and either do nothing and I connect to internet normally without any routed traffic or after switch off/on Internet connection just stops working. I checked the exit node with my phone at it is working properly there.

---

<div class="post-metadata">

**Author:** ![mja311](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/m/858c86/32.png) [@mja311](https://forum.gl-inet.com/u/mja311)\
**Post date:** [August 30, 2024, 7:53pm UTC](https://forum.gl-inet.com/t/how-to-get-tailscale-working-on-the-beryl-mt-1300/31598/10 "2024-08-30T19:53:15Z")

</div>

I have the same issue as mentioned above after step 12

> whilst SSHed into the router I could ping devices on the Tailscale network and on exposed subnets  
> So while SSH'ed into the router, all looks correct, I can ping exposed subnets or IPs from tailscale.

> devices on my home network, couldn’t.  
> But for my devices connected through the router, they can't ping tailscale IPs or local subnets.

I tried the Luci panel edit for adding covered devices: tailscale0, but to no avail. I also tried disabling and re-enabling tailscale.

Given past experience with other firewalls, this feels like it's a routing issue maybe? Since the tailscale client is on the firewall and the firewall can use the TS correctly client, it seems the problem is that clients of the firewall cannot reuse the client installed on the firewall itself?

Tailscale 1.66.4-1 (OpenWrt)  
GL-AXT1800 - 4.6.2

---

<div class="post-metadata">

**Author:** ![mja311](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/m/858c86/32.png) [@mja311](https://forum.gl-inet.com/u/mja311)\
**Post date:** [August 30, 2024, 7:53pm UTC](https://forum.gl-inet.com/t/how-to-get-tailscale-working-on-the-beryl-mt-1300/31598/11 "2024-08-30T19:53:30Z")

</div>

I was actually able to get this to work after more trial and error.

In the Luci interface, I enabled `masquerading` after reading the docs here from tailscale and having setup tailscale on a few dozens devices in the past: [Subnet routers · Tailscale Docs](https://tailscale.com/kb/1019/subnets)

You can see the checkbox for it available here. By default it was UNchecked for me. checking it, save and apply, and reboot worked here.

 ![Screenshot 2024-08-30 at 3.18.55 PM](https://forum-static.gl-inet.com/original/3X/5/b/5b56f39982729d654d5c9802d65e58ea0ce3b703.png)

PS: I also tried creating a file like this from the above document from Tailscale, but proved it isn't needed, my guess is these are set this way out of the box for the GL products given they are routers.

```echo
echo 'net.ipv6.conf.all.forwarding = 1' | sudo tee -a /etc/sysctl.d/99-tailscale.conf
sudo sysctl -p /etc/sysctl.d/99-tailscale.conf
type or paste code here

```

---

<div class="post-metadata">

**Author:** ![CVO](https://forum-assets.gl-inet.com/user_avatar/forum.gl-inet.com/cvo/32/12535_2.png) [@CVO](https://forum.gl-inet.com/u/CVO)\
**Post date:** [September 2, 2025, 9:20pm UTC](https://forum.gl-inet.com/t/how-to-get-tailscale-working-on-the-beryl-mt-1300/31598/12 "2025-09-02T21:20:21Z")

</div>

Is it possible to get a newer firmware release for the MT-1300? It looks like the performance issues may be resolved in 24.10? (Latest MT-1300 firmware is based on 22.03)

> **[\[OpenWrt Wiki\] Tailscale](https://openwrt.org/docs/guide-user/services/vpn/tailscale/start#throughput_improvements_via_transport_layer_offloading_in_openwrt_2410)**

---

<div class="post-metadata">

**Author:** ![CVO](https://forum-assets.gl-inet.com/user_avatar/forum.gl-inet.com/cvo/32/12535_2.png) [@CVO](https://forum.gl-inet.com/u/CVO)\
**Post date:** [September 17, 2025, 4:42pm UTC](https://forum.gl-inet.com/t/how-to-get-tailscale-working-on-the-beryl-mt-1300/31598/13 "2025-09-17T16:42:41Z")

</div>

I upgraded to 1.88.1 via [Smaller Tailscale for OpenWrt](https://gunanovo.github.io/openwrt-tailscale/) and it does work but has the same speed issue / no appreciable increase in performance. It seems like possibly the 24.10 offloading improvements may be the best solution, but without wiping and installing a fresh OpenWRT I’m not sure.

---

<div class="post-metadata">

**Author:** ![Cmegens](https://forum-assets.gl-inet.com/user_avatar/forum.gl-inet.com/cmegens/32/29574_2.png) [@Cmegens](https://forum.gl-inet.com/u/Cmegens)\
**Post date:** [October 25, 2025, 9:23pm UTC](https://forum.gl-inet.com/t/how-to-get-tailscale-working-on-the-beryl-mt-1300/31598/14 "2025-10-25T21:23:07Z")

</div>

My MT-1300 doesn’t show gl-sdk4-tailscale in the plugins at all? I’m at 4.3.25

---

<div class="post-metadata">

**Author:** ![will.qiu](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/w/b38774/32.png) [@will.qiu](https://forum.gl-inet.com/u/will.qiu)\
**Post date:** [August 13, 2026, 9:26am UTC](https://forum.gl-inet.com/t/how-to-get-tailscale-working-on-the-beryl-mt-1300/31598/15 "2026-08-13T09:26:36Z")

</div>


