MiFi QMI Driver for Quectel EC20 and UC20

rangerz · 2016-10-28T05:07:51.000Z

My config is as follows:

config interface ‘modem’
option proto ‘wwan’
option country ‘country73’
option sp ‘isp0’
option device ‘/dev/ttyUSB3’
option service ‘umts’
option dialnum ‘*99#’
option apn ‘broadband’
option username ‘WAP@CINGULAR.COM’
option password ‘CINGULAR1’
option metric ‘40’

but I too am not connecting. I also tried this:

config interface ‘modem’
option proto ‘qmi’
option country ‘country73’
option sp ‘isp0’
option modes ‘lte’
option dialnum ‘*99#’
option apn ‘broadband’
option username ‘WAP@CINGULAR.COM’
option password ‘CINGULAR1’
option metric ‘40’
option device ‘/dev/cdc-wdm0’
Why are you having the above in the section for ‘wan’, should this not be ‘modem’?

For others, some additional reference

https://wiki.openwrt.org/doc/uci/network#protocol_qmi_usb_modems_using_qmi_protocol

https://wiki.openwrt.org/doc/uci/network#protocol_wwan_usb_modems_autodetecting_above_protocols

I also notice that for proto wwan there is option ‘service’, but for proto qmi there is option ‘modes’, which you have embraced.

With the default GUI config the logs specifically ref the Quectel EC20:

Wed Oct 26 14:42:08 2016 daemon.notice netifd: Interface ‘modem’ is setting up now
Wed Oct 26 14:42:08 2016 daemon.notice netifd: modem (2759): wwan[2759] Using proto:wwan device:/dev/cdc-wdm0 iface:wwan0 desc:Quectel EC20
Wed Oct 26 14:42:08 2016 daemon.notice netifd: modem (2759): Waiting for network registration
Wed Oct 26 14:42:08 2016 daemon.notice netifd: modem (2759): Starting network broadband
Wed Oct 26 14:42:09 2016 daemon.notice netifd: modem (2759): Unable to connect IPv4
Wed Oct 26 14:42:09 2016 daemon.notice netifd: modem (2759): Unable to connect IPv6
Wed Oct 26 14:42:09 2016 daemon.notice netifd: modem (2759): Unable to connect
Wed Oct 26 14:42:09 2016 daemon.notice netifd: modem (2858): Stopping network
Wed Oct 26 14:42:10 2016 daemon.notice netifd: modem (2858): Command failed: Permission denied
Wed Oct 26 14:42:10 2016 daemon.notice netifd: Interface ‘modem’ is now down

With the QMI config I get this:

Wed Oct 26 14:42:43 2016 daemon.notice netifd: Interface ‘modem’ is setting up now
Wed Oct 26 14:42:43 2016 daemon.notice netifd: modem (3858): Waiting for network registration
Wed Oct 26 14:42:49 2016 daemon.notice netifd: modem (3858): Starting network broadband
Wed Oct 26 14:42:49 2016 daemon.notice netifd: modem (3858): Unable to connect IPv4
Wed Oct 26 14:42:49 2016 daemon.notice netifd: modem (3858): Unable to connect IPv6
Wed Oct 26 14:42:49 2016 daemon.notice netifd: modem (3858): Unable to connect
Wed Oct 26 14:42:49 2016 daemon.notice netifd: modem (3951): Stopping network
Wed Oct 26 14:42:49 2016 daemon.notice netifd: modem (3951): Command failed: Permission denied
Wed Oct 26 14:42:49 2016 daemon.notice netifd: Interface ‘modem’ is now down

heavymetal · 2016-10-28T16:20:52.000Z

Hi @RangerZ the “config interface” is just for giving the interface the name which can be anything.

alzhao · 2016-10-29T11:34:49.000Z

@heavymetal,

Maybe you can try this:

config interface ‘wan’
~~option device ‘/dev/cdc-wdm0’~~
option proto ‘qmi’
option apn ‘ltedata.apn’

option ifname ‘wwan0’
~~option modes ‘all’~~

heavymetal · 2016-10-30T00:06:53.000Z

Hi @alzhao, I just tried the above config and now I get this in the log:

Sat Oct 29 11:57:53 2016 daemon.notice netifd: Interface ‘wan’ is setting up now
Sat Oct 29 11:57:54 2016 daemon.notice netifd: wan (1699): No control device specified
Sat Oct 29 11:57:54 2016 daemon.notice netifd: wan (1744): Stopping network
Sat Oct 29 11:57:55 2016 daemon.notice netifd: wan (1744): Command failed: Permission denied
Sat Oct 29 11:57:55 2016 daemon.notice netifd: Interface ‘wan’ is now down

Thanks

heavymetal · 2016-11-01T11:19:39.000Z

I have done another test with the signal stats below and can see an improvement over serial mode:

“type”: “hdr”,
“rssi”: -125,
“ecio”: 5,
“io”: -106,
“type”: “lte”,
“rssi”: -49,
“rsrq”: -8,
“rsrp”: -79,
“snr”: 166

Also I have noticed when it looses signal the 3G / 4G LED stays lit.

heavymetal · 2016-11-02T14:18:28.000Z

I have updated to 2.23-7 and can confirm that qmi settings are now working again:

config interface ‘wan’
option proto ‘qmi’
option device ‘/dev/cdc-wdm0’
option apn ‘ltedata.apn’
option mode ‘all’

As for dual-stack I wonder if this will help add the functionality in functionality in OpenWrt Forum Archive

Thanks

alzhao · 2016-11-02T16:28:13.000Z

@heavymetal, in 2.23-7 I used the most updated uqmi you mentioned.

Are you able to try something on it?

heavymetal · 2016-11-04T13:15:25.000Z

I have finally gotten IPv6 dual-stack to work over 4G.

I have to manually write a connect script that runs at startup here: https://paste.aseriesoftubez.com/p/1478235776-wULPV.txt

After the script runs and it will restart networking in OpenWRT then it will get IPv4 and IPv6 address on the wwan0 interface.

alzhao · 2016-11-04T16:06:18.000Z

thanks for sharing

rangerz · 2016-11-05T01:29:54.000Z

@heavymetal. I am not a script genie, but it appears I would need to substitute my apn value for ltedata.apn. Any idea if I would also need to pass the dial number, user and password I have in my script? If so are you able to help with the correct paramaters?

Are you on 2.23-7?

heavymetal · 2016-11-05T06:05:19.000Z

Hi @RangerZ yes you will have to replace “ltedata.apn” with “Broadband” from ATT without the quotes.

According to https://www.att.com/esupport/article.html#!/wireless/KM1062162 you do not have to set any dial number, username, and password.

rangerz · 2016-11-06T00:10:30.000Z

Thanks, I have tried the following config with, and without the last three lines. Only the uqmi-ipv6.log was generated with results below for all tests. Not sure what this is telling us, other than there is a problem.

config interface ‘modem’
option proto ‘qmi’
option device ‘/dev/cdc-wdm0’
option mode ‘all’
option apn ‘broadband’
option username ‘WAP@CINGULAR.COM’
option password ‘CINGULAR1’
option dialnum ‘*99#’

uqmi-ipv6 script output:
IPv6 Stop: “No effect”
IPv6 client-id: 6
Connection v6 ID: “Call failed”
IPv4 client-id: 7
Connection v4 ID: “Call failed”

heavymetal · 2016-11-08T15:58:52.000Z

Hi @RangerZ I forgot to mention that my modem interface config is just using DHCP as that script above will connect to the mobile network.

Here is what my config looks like for the modem:

config interface ‘wan’
option proto ‘dhcp’
option ifname ‘wwan0’

config interface ‘wan6’
option proto ‘dhcpv6’
option ifname ‘wwan0’
option reqprefix ‘auto’
option peerdns ‘0’
option reqaddress ‘try’

komeilkma · 2019-09-23T09:29:22.365Z

hi my friend
i can get ipv6 from qmi in wwan0
but not test ipv6 in test-ipv6.com . i cant get ipv6 public from isp but can get ipv6 private in wwan0
how i can solce this ? very thanks

robotluo · 2019-09-23T10:44:34.730Z

IPV6 addresses are provided by the carrier. Does your carrier support IPV6?

komeilkma · 2019-09-23T10:59:36.550Z

yes isp support ipv6 and test-ipv6.com get this message for check my isp :
Your DNS server (possibly run by your ISP) appears to have IPv6 Internet access

robotluo · 2019-09-23T11:13:39.447Z

We haven’t actually tested IPV6 yet.
you can look at the file /lib/netifd/proto/qmi.sh, this file contains the procedure for the router to obtain IP from the carrier

markusk · 2023-11-13T17:36:25.155Z

alzhao:

Second, about the config. Now in Internet settings, you can choose 3G tab, then choose country, service provider, ttyUSB3, UMTS and then click submit.

(how) should this work with 3.x firmware?

alzhao · 2023-11-16T06:15:50.783Z

Sorry cannot answer a 3-year old thread.

alzhao · 2023-11-16T06:15:56.157Z