# MT6000/ Flint 2 firmware 4.9.1 IoT support

**URL:** <https://forum.gl-inet.com/t/mt6000-flint-2-firmware-4-9-1-iot-support/70554>\
**Category:** Router\
**Created:** [August 13, 2026, 11:21am UTC](https://forum.gl-inet.com/t/mt6000-flint-2-firmware-4-9-1-iot-support/70554 "2026-08-13T11:21:51Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![esselite](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/e/34f0e0/32.png) [@esselite](https://forum.gl-inet.com/u/esselite)\
**Post date:** [August 13, 2026, 11:21am UTC](https://forum.gl-inet.com/t/mt6000-flint-2-firmware-4-9-1-iot-support/70554/1 "2026-08-13T11:21:51Z")

</div>

What’s the point adding IoT support if any AP connetced to the router won’t re-distribute this IoT network?

I have 2nd Flint2 device connected with LAN and 2nd router is not propagating any IoT network that is setup on 1st device. Why IoT cannot be distributed by AP?

---

<div class="post-metadata">

**Author:** ![charles2](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/c/9dc877/32.png) [@charles2](https://forum.gl-inet.com/u/charles2)\
**Post date:** [August 14, 2026, 7:31am UTC](https://forum.gl-inet.com/t/mt6000-flint-2-firmware-4-9-1-iot-support/70554/3 "2026-08-14T07:31:30Z")

</div>

Hi,

The IoT network created on the main Flint 2 is a separate network from the Main LAN. When the second Flint 2 is connected in AP mode through a normal Ethernet connection, it will not automatically inherit and extend the IoT network configured on the main router.

If you want the second Flint 2 to provide the same Main / Guest / IoT networks while keeping them separated, VLANs are required to distinguish these networks over the Ethernet connection between the two devices. The connection between the two routers needs to carry the corresponding VLANs, and the VLANs can then be mapped to the appropriate SSIDs on the second Flint 2.

If this is what you would like to achieve, you can refer to the following example from another model/firmware version with similar requirements:

> [@Flint 3 (GL-BE9300) as AP behind pfSense: multiple SSIDs -\> VLAN + Random BSSID](https://forum.gl-inet.com/t/flint-3-gl-be9300-as-ap-behind-pfsense-multiple-ssids-vlan-random-bssid/66719/4):
>
> Hi Well, overall your requirements are feasible. However, the configuration will be quite complex, and it requires you to have sufficient knowledge of networking concepts as well as a solid understanding of LuCI/UCI. Below is a configuration example. Since the steps for Work and IoT are repetitive, only Main / Guest / IoT are used as examples here. Topology is as follows: Configuration steps: Start from a factory-default BE9300 v4.8.3 configuration Configure its WAN port as …

Thank you for your support and understanding.

---

<div class="post-metadata">

**Author:** ![esselite](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/e/34f0e0/32.png) [@esselite](https://forum.gl-inet.com/u/esselite)\
**Post date:** [August 15, 2026, 12:06am UTC](https://forum.gl-inet.com/t/mt6000-flint-2-firmware-4-9-1-iot-support/70554/4 "2026-08-15T00:06:20Z")

</div>

Thanks. I have asked ChatGPT to deliver me final status and he directed me line by line on the cofiguration , with checkpoints. All is completed. That was effective, as it was providing exact commands that should be entered in SSH Terminal.

```auto
                MAIN GL-MT6000

Main LAN
192.168.50.0/24
     |
     | untagged / native
     |
    LAN5
     |
     +-----------------------------+
     | |
     | VLAN 107 tagged | VLAN 9 tagged
     | |
     v v
IoT network Guest network
192.168.107.0/24 192.168.9.0/24
br-iot br-guest
     | |
     +------------- Ethernet trunk +
                   |
                   v
             ACCESS POINT

eth1 -> Main / untagged
eth1.107 -> br-iot
eth1.9 -> br-guest

```

The Main router is the only device doing routing, DHCP and firewalling:

- Main: `192.168.50.0/24`

- IoT: `192.168.107.0/24`

- Guest: `192.168.9.0/24`

The AP is only bridging Wi-Fi clients into the appropriate VLAN/network.

DHCP for IoT and Guest comes from the Main router through the tagged VLANs.

I tested both VLANs end-to-end:

- IoT client connected to the AP receives a `192.168.107.x` address and Internet access.

- Guest client connected to the AP receives a `192.168.9.x` address and Internet access.

- Guest clients are isolated from Main and IoT by the firewall on the Main router.

---

<div class="post-metadata">

**Author:** ![system](https://forum-static.gl-inet.com/original/3X/7/7/77e28f6cb342ac4bd641bd9a6254595d61b2812a.png) [@system](https://forum.gl-inet.com/u/system)\
**Post date:** [November 11, 2026, 11:22am UTC](https://forum.gl-inet.com/t/mt6000-flint-2-firmware-4-9-1-iot-support/70554/5 "2026-11-11T11:22:29Z")

</div>

This topic was automatically closed after 90 days. New replies are no longer allowed.
