New to the GLiNet can not see the USB or micro

wellis · 2022-12-22T23:10:12.815Z

I just got aGL-MT1300 and put the microSD card in. I can not see it even though I have rebooted several times. I tried a USB, and I can not see that either. The USB worked in my old MT300.
Is there a guide for how to mount these drives or should it work. I can connect to the file share but I see only Record and Time_lapse - I am assuming that they are the internal storage.

agent_smith · 2022-12-22T23:38:06.783Z

Hello.
what firmware are you using?
If you use the firmware v3.x, then perhaps you should confirm the installation of FILE Sharing in the Glinet interface Applications>File Sharing > File Sharing Install (this requires an Internet).
Could you please share a screenshot of this settings with USB/SD Card in?

wellis · 2022-12-23T01:24:36.467Z

Screenshot 2022-12-22 at 8.20.39 PM1290×674 29.9 KB

Screenshot 2022-12-22 at 8.20.26 PM2108×1642 231 KB

wcs2228 · 2022-12-23T02:42:34.529Z

wellis:

I can connect to the file share but I see only Record and Time_lapse - I am assuming that they are the internal storage.

To confirm, you are able to connect to the microSD card? I think the router uses “GL-Samba” as the default share name. If so, can you check if “Record” and “Time_lapse” are file/folders on the microSD card?

You can also log into the router via SSH and run the following commands:

This will show all the mounted devices -

df

This will show the contents of the microSD card mount point -

ls -l /mnt/mmcblk0p1

Here is the official GL.iNet documentation on File Sharing for your GL-MT1300:

docs.gl-inet.com

File Sharing - GL.iNet Router Docs 3

Documentation for GL.iNet Router Productions

I do not work for and I do not have formal association with GL.iNet.

alzhao · 2022-12-23T03:09:15.448Z

wellis:

I can connect to the file share but I see only Record and Time_lapse - I am assuming that they are the internal storage.

Can you give a screenshot of “Time_lapse”? Not sure what it is.

wellis · 2022-12-23T03:35:51.280Z

Sadly I can not SSH into the router… something in the config must be wrong…
Unable to negotiate with 192.168.8.1 port 22: no matching host key type found. Their offer: ssh-rsa

wellis · 2022-12-23T03:39:19.383Z

Screenshot 2022-12-22 at 10.38.22 PM1390×178 18.8 KB

wcs2228 · 2022-12-23T03:39:33.870Z

You can download the free PuTTY at https://www.putty.org/. It will allow you to accept using without the host key.

LupusE · 2022-12-23T07:38:10.047Z

Just search for:

wellis:

no matching host key type found

It will get some answer, for example: Ssh issues - #2 by LupusE

[…]
One time:
ssh -oHostKeyAlgorithms=+ssh-rsa root@192.168.8.1

Permanent:
echo -e “\tHostKeyAlgorithms ssh-rsa” >> .ssh/config
[…]

The error says “I ask for a set of ‘key types’, none is okay for the host. It demands ssh-rsa”. And oHostKeyAlgorithms=+ssh-rsa adds this ‘type’ to the offered choices.

K3rn3l_Ku5h · 2022-12-24T14:03:24.424Z

wellis:

The USB worked in my old MT300.

Did you unmount the card properly before moving it? might have corrupted the data.
Did you format the card on a computer before trying to mount it on the router?