Openvpn site-to-site

samu92 · 2019-09-19T05:50:03.200Z

thanks, now from the node I can access the main but not the other way around. should it be possible?

robotluo · 2019-09-19T06:28:56.851Z

If you want to reverse access, you need to add subnets to the corresponding node

samu92 · 2019-09-19T17:13:00.530Z

it works, thanks for the support. I have only one question, now to access I must be connected to the LAN port of the two devices. now how can I access my home network directly so as to keep the device attached to the router with only the Wan cable?

robotluo · 2019-09-20T01:49:18.269Z

Do you need direct access to your home network from the Internet?
Why don’t you just open a port on your home router?
You can also turn on the 300N-V2’s remote access and access your home network through the router.

%5BJADJQMYFKN13G6L%7DN5KU5D1116×513 22.5 KB

samu92 · 2019-09-20T05:20:33.288Z

no, I would like to use my MT300N-VN as if it were a PC connected to my home network and then with only one cable on the Wan port. it’s possible? so that from my home network I can access the remote network

robotluo · 2019-09-20T07:33:04.349Z

To build a site2site network, at least one node must have a public IP. If not, you need to set up port forwarding on your main router

samu92 · 2019-09-20T07:47:05.003Z

right, my device is connected to my adsl router via Wan but if I try to access the network of my second device via VPN from the PC connected to my adsl router it does not work.

robotluo · 2019-09-20T08:03:08.840Z

You’d better draw a simple topology

samu92 · 2019-09-20T08:36:52.011Z

Presentazione%20standard11280×720 38.3 KB

robotluo · 2019-09-20T09:59:35.334Z

samu92:

right, my device is connected to my adsl router via Wan but if I try to access the network of my second device via VPN from the PC connected to my adsl router it does not work.

Where is the “second device”?

samu92 · 2019-09-20T10:02:07.617Z

the second device is the VPN client with GL-Inet

robotluo · 2019-09-20T10:39:45.580Z

You need to configure the adls router and add a static routing table
Assuming your adls LAN interface is br-lan, you may need to add routing rules like the following

ip route add 192.168.10.0/24 dev br-lan

YK(03HTU4%7B44G12H%25LJ_Z8D896×500 39.5 KB

samu92 · 2019-09-20T11:27:49.874Z

my adsl router does not allow to do this. Is it possible to do it from GL-Inet?

robotluo · 2019-09-21T01:16:16.909Z

Your adsl router doesn’t have the correct routing rules, so the data won’t go to gl-router at all, there’s no other way for now

samu92 · 2019-09-23T08:10:30.927Z

would the installation of a gateway be a solution?

robotluo · 2019-09-23T08:34:54.360Z

With gateways, you also need to configure static routing rules

stook84 · 2019-12-11T07:20:37.410Z

hi I don’t have this in my devices

222060×1034 175 KB

alzhao · 2019-12-11T08:02:21.339Z

what is your device model and firmware version?

go to dl.gl-inet.com and find a beta firmware for your device.

stook84 · 2019-12-11T08:39:20.104Z

this is mine GL.iNet GL-MT300N-V2

robotluo · 2019-12-11T10:30:40.215Z

Please try this firmware.