I have a GL-AR300M and have a problem with a new USB-stick (128GB USB-3 from Intenso).
The stick works fine on my PC and my phone, however it does not show up on the usb-bus on the router (it is connected via a powered hub).
Looking at dmesg I see this:
[ 51.823886] usb 1-1.1.1: reset full-speed USB device number 5 using ehci-platform
[ 67.083882] usb 1-1.1.1: device descriptor read/64, error -145
[ 72.423880] usb 1-1.1.1: device descriptor read/64, error -71
[ 72.643873] usb 1-1.1.1: reset full-speed USB device number 5 using ehci-platform
[ 72.843871] usb 1-1.1.1: device descriptor read/64, error -71
[ 73.153869] usb 1-1.1.1: device descriptor read/64, error -71
[ 73.373880] usb 1-1.1.1: reset full-speed USB device number 5 using ehci-platform
[ 73.873872] usb 1-1.1.1: device not accepting address 5, error -71
[ 73.973879] usb 1-1.1.1: reset full-speed USB device number 5 using ehci-platform
[ 74.473867] usb 1-1.1.1: device not accepting address 5, error -71
[ 74.483680] usb 1-1.1.1: USB disconnect, device number 5
I’ve tried it again and the stick showed up for a very brief moment before disappearing again.
What is happening here?
dmesg shows:
[52576.535510] usb-storage 1-1.1.1:1.0: USB Mass Storage device detected
[52576.553360] scsi host0: usb-storage 1-1.1.1:1.0
[52577.710686] scsi 0:0:0:0: Direct-Access Intenso Speed Line 1100 PQ: 0 ANSI: 6
[52577.726599] sd 0:0:0:0: [sda] 250183680 512-byte logical blocks: (128 GB/119 GiB)
[52577.737593] sd 0:0:0:0: [sda] Write Protect is off
[52577.742577] sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00
[52577.750593] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn’t support DPO or FUA
[52577.785742] sda: sda1
[52577.804629] sd 0:0:0:0: [sda] Attached SCSI removable disk
[52608.913014] usb 1-1.1.1: reset full-speed USB device number 19 using ehci-platform
[52624.172865] usb 1-1.1.1: device descriptor read/64, error -145
[52629.512834] usb 1-1.1.1: device descriptor read/64, error -71
[52629.732842] usb 1-1.1.1: reset full-speed USB device number 19 using ehci-platform
[52629.932862] usb 1-1.1.1: device descriptor read/64, error -71
[52630.242849] usb 1-1.1.1: device descriptor read/64, error -71
[52630.462841] usb 1-1.1.1: reset full-speed USB device number 19 using ehci-platform
[52630.962859] usb 1-1.1.1: device not accepting address 19, error -71
[52631.062861] usb 1-1.1.1: reset full-speed USB device number 19 using ehci-platform
[52631.562832] usb 1-1.1.1: device not accepting address 19, error -71
[52631.572548] usb 1-1.1.1: USB disconnect, device number 19
[52631.581706] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[52631.588415] sd 0:0:0:0: [sda] tag#0 UNKNOWN(0x2003) Result: hostbyte=0x01 driverbyte=0x00
[52631.596954] sd 0:0:0:0: [sda] tag#0 CDB: opcode=0x28 28 00 00 00 01 10 00 00 f0 00
[52631.604799] blk_update_request: I/O error, dev sda, sector 272
[52631.613755] sda: detected capacity change from 128094044160 to 0
[52631.620201] sd 0:0:0:0: [sda] Synchronize Cache(10) failed: Result: hostbyte=0x01 driverbyte=0x00
[52631.752890] usb 1-1.1.1: new full-speed USB device number 20 using ehci-platform
[52631.952900] usb 1-1.1.1: device descriptor read/64, error -71
[52632.272868] usb 1-1.1.1: device descriptor read/64, error -71
[52632.492912] usb 1-1.1.1: new full-speed USB device number 21 using ehci-platform
[52632.692897] usb 1-1.1.1: device descriptor read/64, error -71
[52633.002891] usb 1-1.1.1: device descriptor read/64, error -71
[52633.124607] usb 1-1.1-port1: attempt power cycle
[52633.782870] usb 1-1.1.1: new full-speed USB device number 22 using ehci-platform
[52634.292873] usb 1-1.1.1: device not accepting address 22, error -71
[52634.422871] usb 1-1.1.1: new full-speed USB device number 23 using ehci-platform
[52634.922803] usb 1-1.1.1: device not accepting address 23, error -71
[52634.930564] usb 1-1.1-port1: unable to enumerate USB device