Site To Site clients cannot reach each other

databass · 2021-09-07T13:05:00.106Z

Hi,

I am trying to get a PC on my home network to connect to a device on a remote network. I have two Routers:
-Router One is connected to my home broadband Router (I have forwarded Port 51830 to facilitate Site To Site). IP is 192.168.8.1
-Router Two is connected to a mobile broadband USB Dongle. IP is 192.168.207.1.

I added the Devices in GoodCloud and successfully configured a Site To Site network. I can ping both routers from any client on the network, however I can cannot ping between Clients which sit under the different Routers.

I thought that leaving “Allow be Access for the Following Subnets” set with 192.168.8.0/24 and 192.168.207.0/24 would mean any client can reach any other client but that doesn’t appear to be the case. Am I missing some configuration?

alzhao · 2021-09-08T09:20:29.233Z

databass:

I thought that leaving “Allow be Access for the Following Subnets” set with 192.168.8.0/24 and 192.168.207.0/24 would mean any client can reach any other client but that doesn’t appear to be the case. A

This should be the correct settings.

Can you post screeshot?

databass · 2021-09-08T10:22:14.609Z

Thanks Alzhao - screenshots below.

Site to Site Config

1) Site to Site Config 1929×428 23.2 KB

databass · 2021-09-08T10:22:47.782Z

2) Site to Site Config 21011×575 28.9 KB

databass · 2021-09-08T10:24:01.729Z

3) Site to Site Config 3513×533 14.9 KB

databass · 2021-09-08T10:25:20.650Z

Pings
I connected my machine to the WiFi of Router 1 and pinged the two Routers and then a client on Router 2.
Then I connected to the WiFi of Router and did the same.
As you can see, I can only ping the client when connected to Router 2 directly (not through Site to Site)

4) Ping Router and Client 1477×644 12.8 KB

databass · 2021-09-08T10:25:51.969Z

5) Ping Router and Client 2469×721 15.4 KB

databass · 2021-09-12T09:00:18.473Z

Any further idea based on the screenshots posted?

Leo · 2021-09-13T09:33:20.217Z

What is the service you want to remote access in another Site to Site node? I mean what is the service running on 192.168.8.203? A website? FTP? or ?

databass · 2021-09-15T11:14:09.797Z

182.168.8.203 is just a test (it’s another PC) and I’ve included as a simple example for troubleshooting purposes.

Shouldn’t every client be accessible using site to site?

Leo · 2021-09-18T12:56:05.495Z

I just test it, ping another Mac on Main Node (192.168.28.188), it work. Could you give more detail of your problem? A typology network diagram is great.

goodcloud_site_to_site_ping964×484 98.6 KB

databass · 2021-09-20T09:10:22.739Z

Network diagram:

Network1280×720 80.6 KB

What should I need to configure for this to work?
Is there something about the extra Router that might be causing a problem?

databass · 2021-09-20T10:58:03.349Z

I have just realised my mistake - the PC firewall was blocking the ping requests.

Thanks for the responses and apologies for the time wasting.

Leo · 2024-09-20T01:54:27.586Z