请问有人知道这设备怎么用吗？登录密码是什么？怎么刷新固件？

1922411572_QQ · 2019-12-20T03:12:31.688Z

请问有人知道这设备怎么用吗？登录密码是什么？怎么刷新固件？不知怎么在帖子里贴图，上传不了图片。一个小方块，gl-inet6416A芯片，S/N d28b3c63fd4aaf88，登录地址是192.168.134.1，LAN、WAN口各1个，1个USB2.0，1个miniUSB口，1个reset按键。我电子邮箱1922411572@qq.com

alzhao · 2019-12-20T06:07:19.078Z

看不到图片解释不清楚，但是不是我们自己的固件，也不知道密码。你试试uboot刷固件吧。

1922411572_QQ · 2019-12-20T06:49:53.706Z

uboot openwrt-6416-2.264.bin后，LED红灯长亮，但无论是192.168.8.1，还是192.168.134.1都不能登录。谢谢您！

1922411572_QQ · 2019-12-20T06:52:54.214Z

能否把您的邮箱地址发给我，我把图片发给您，麻烦您帮帮忙

alzhao · 2019-12-20T07:27:33.668Z

是192.168.1.1啊。

按这个Debrick via Uboot - GL.iNet Docs

1922411572_QQ · 2019-12-20T08:23:36.844Z

https://docs.gl-inet.com/en/3/troubleshooting/debrick/这个网址我这儿打不开。192.168.1.1uboot openwrt-6416-2.264.bin，LED闪亮几次后红灯长亮，之后设IP为自动获取或相应网址，但无论是192.168.8.1，还是192.168.134.1都不能登录

alzhao · 2019-12-20T08:31:15.310Z

First you have to download firmware to your computer. You can download the firmware here. For GL-AR300M, GL-AR300M-Ext, GL-AR750S-Ext, please download the .img firmware file. For GL-B1300, GL-S1300, please download the .img firmware. Everyone else, download the .bin firmware file.
Connect your computer to the Ethernet port (either LAN or WAN) of the router. You MUST leave the other port unconnected .
Press and hold the Reset button firmly first, and then power on your device. (If your device does not have a power button, plugging it in will power it on automatically.)
The Power LED will light up. Then, other LEDs will start flashing.
Release your finger when you see the LED has flashed:

6 times for GL-MiFi, and then the LTE light will faintly flash twice.
5 times for GL-AR150, GL-AR300M, GL-USB150, GL-AR750, GL-AR750S-Ext (Slate), GL-X750-Ext (Spitz), GL-MT300N-V2.
4 times for GL-S1300, GL-B1300.

The leftmost LED may stay on the whole time while the rightmost LED flashes 4 times, then the middle LED turns on and stays on.

(For some old GL-B1300, the leftmost LED stays on the whole time, and both the middle LED and the rightmost LED flash 5 times at the same time then they stay on.)

3 times for GL-MT300N, GL-MT300A.

Set your computer’s IP address to 192.168.1.2 . Please check the step-by-step guide for different operating systems below:

1922411572_QQ · 2019-12-20T09:16:59.159Z

I did it. The LED is also blinking. I know the firmware should be written. Then the red light stayed on.