# Troubleshooting Nanoleaf light pannels with MT300N-V2

**URL:** <https://forum.gl-inet.com/t/troubleshooting-nanoleaf-light-pannels-with-mt300n-v2/24563>\
**Category:** Router\
**Created:** [October 12, 2022, 10:46am UTC](https://forum.gl-inet.com/t/troubleshooting-nanoleaf-light-pannels-with-mt300n-v2/24563 "2022-10-12T10:46:07Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![smart.desk9538](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/s/ac8455/32.png) [@smart.desk9538](https://forum.gl-inet.com/u/smart.desk9538)\
**Post date:** [October 12, 2022, 10:46am UTC](https://forum.gl-inet.com/t/troubleshooting-nanoleaf-light-pannels-with-mt300n-v2/24563/1 "2022-10-12T10:46:07Z")

</div>

Thee lights suppose to pair with the mobile or desktop app and that's how they connect to home WiFi.  
Most of the time, this pairing problem can be solved with the right network settings.  
I need to satisfy a couple of settings of my MT300N-V2 router:

#### 1. UPnP (enabled)

✅ I installed luci-app-upnp, miniupdpd and enabled inside LuCi.

#### 2. Multicast (enabled) and IGMP Snooping (enabled)

✅ Enabled **v3** at GL UI admin panel/Applications/IGMP Snooping

#### 3. Client/AP Isolation (disabled)

I don't have Advance tab with that setting inside LuCi/Network/Wireless//Edit/Interface Configuration. Guest network is disabled if that's relevant.

#### 4. (opt) test with TKIP

 ![image](https://forum-static.gl-inet.com/original/2X/a/a4f49a4b884d0595348f8a9007cd3c7ef1e88eaf.jpeg)  
Additionally, I would like to test it out with TKIP instead AES security protocol. How do I do that?

* * *

I run 3.211 firmware.  
MT300N-V2 is connected by Ethernet cable to the generic ISP router (wlan disabled)  
My NAS is connected to MT300N-V2 and has static IP address set.

How else can I make sure my network is ready to accept Nanoleaf device in the network?

---

<div class="post-metadata">

**Author:** ![yuxin.zou](https://forum-assets.gl-inet.com/user_avatar/forum.gl-inet.com/yuxin.zou/32/11475_2.png) [@yuxin.zou](https://forum.gl-inet.com/u/yuxin.zou)\
**Post date:** [October 13, 2022, 2:45am UTC](https://forum.gl-inet.com/t/troubleshooting-nanoleaf-light-pannels-with-mt300n-v2/24563/2 "2022-10-13T02:45:43Z")

</div>

> [@smart.desk9538](#):
>
> Additionally, I would like to test it out with TKIP instead AES security protocol. How do I do that?

This settings is not supported on GL UI yet, you need to set it up using LuCI or manually modify `/etc/config/wireless` by referring to [the wiki](https://openwrt.org/docs/guide-user/network/wifi/basic#encryption_modes).

---

<div class="post-metadata">

**Author:** ![alzhao](https://forum-assets.gl-inet.com/letter_avatar_proxy/v4/letter/a/5f9b8f/32.png) [@alzhao](https://forum.gl-inet.com/u/alzhao)\
**Post date:** [October 13, 2022, 9:46am UTC](https://forum.gl-inet.com/t/troubleshooting-nanoleaf-light-pannels-with-mt300n-v2/24563/3 "2022-10-13T09:46:26Z")

</div>

Use WPA/WPA2-PSK

I found some IoT devices like this encryption.

---

<div class="post-metadata">

**Author:** ![bruce](https://forum-assets.gl-inet.com/user_avatar/forum.gl-inet.com/bruce/32/35649_2.png) [@bruce](https://forum.gl-inet.com/u/bruce)\
**Post date:** [October 29, 2025, 4:19am UTC](https://forum.gl-inet.com/t/troubleshooting-nanoleaf-light-pannels-with-mt300n-v2/24563/4 "2025-10-29T04:19:10Z")

</div>