Using ATX1800 with QUECTEL EM160R-GL

otacon24 · 2022-08-23T18:26:34.153Z

It looks like the modem is being detected from what i can tell, and in QMI mode so that is good. How do I install modem manager on this modem? i’ve search and only found instructions using device specif firmware with modem manager in it.

Wed Aug 17 04:27:54 2022 kern.info kernel: [ 15.123378] NET: Registered protocol family 24
Wed Aug 17 04:27:54 2022 kern.info kernel: [ 15.127197] usbcore: registered new interface driver qmi_wwan
Wed Aug 17 04:27:54 2022 kern.info kernel: [ 15.131359] usbcore: registered new interface driver rndis_host
Wed Aug 17 04:27:54 2022 kern.info kernel: [ 15.294612] usbcore: registered new interface driver option
Wed Aug 17 04:27:54 2022 kern.info kernel: [ 15.294682] usbserial: USB Serial support registered for GSM modem (1-port)

otacon24 · 2022-08-23T18:56:06.559Z

Sorry did find CLI commands for

opkg update

opkg install modemmanager

which were successful but i have no modemmanger option under the wwan interface

i7bar · 2022-08-24T18:41:04.819Z

otacon24:

which were successful but i have no modemmanger option under the wwan interface

Are you sure that it is not available in “Protocol” drop down list ?

otacon24 · 2022-08-24T22:19:30.314Z

Not from what I can tell

Screen Shot 2022-08-23 at 1.44.07 PM1880×820 85.7 KB

i7bar · 2022-08-24T22:35:35.043Z

That is because no device is assigned to this interface. I am not sure how to proceed, you should probably check the log, may be it contains a clue

seva · 2022-10-25T09:18:13.132Z

Do you have any updates on better support of higher cat modems in question?

Thanks

alzhao · 2022-10-25T09:37:27.310Z

We are working on a list of USB modems.

Pls allow a few weeks and we will upgrade the firmware with modem support.

i7bar · 2022-12-11T22:46:29.430Z

Latest firmware 4.1.0 release 7, clean install, EM160R-GL is attached in the external USB3 enclosure.
Looking at the log in luci the modem has been detected:

Sun Dec 11 22:31:20 2022 kern.info kernel: [ 14.862323] usbcore: registered new interface driver cdc_ether
Sun Dec 11 22:31:20 2022 kern.info kernel: [ 14.866620] usbcore: registered new interface driver cdc_ncm
Sun Dec 11 22:31:20 2022 kern.info kernel: [ 14.928528] usbcore: registered new interface driver huawei_cdc_ncm
Sun Dec 11 22:31:20 2022 kern.info kernel: [ 15.072321] PPP generic driver version 2.4.2
Sun Dec 11 22:31:20 2022 kern.info kernel: [ 15.073913] NET: Registered protocol family 24
Sun Dec 11 22:31:20 2022 kern.info kernel: [ 15.106629] qmi_wwan 2-1:1.4: cdc-wdm0: USB WDM device
Sun Dec 11 22:31:20 2022 kern.info kernel: [ 15.106657] qmi_wwan 2-1:1.4: QuectelEC25&EC21&EG91&EG95&EG06&EP06&EM06&BG96&AG35 work on RawIP mode
Sun Dec 11 22:31:20 2022 kern.info kernel: [ 15.112074] qmi_wwan 2-1:1.4 wwan0: register ‘qmi_wwan’ at usb-xhci-hcd.0.auto-1, WWAN/QMI device, aa:c0:a5:87:c9:99
Sun Dec 11 22:31:20 2022 kern.info kernel: [ 15.120190] usbcore: registered new interface driver qmi_wwan
Sun Dec 11 22:31:20 2022 kern.info kernel: [ 15.132078] usbcore: registered new interface driver rndis_host
Sun Dec 11 22:31:20 2022 kern.info kernel: [ 15.290951] usbcore: registered new interface driver option
Sun Dec 11 22:31:20 2022 kern.info kernel: [ 15.291023] usbserial: USB Serial support registered for GSM modem (1-port)
Sun Dec 11 22:31:20 2022 kern.info kernel: [ 15.295507] option 2-1:1.0: GSM modem (1-port) converter detected
Sun Dec 11 22:31:20 2022 kern.info kernel: [ 15.302533] usb 2-1: GSM modem (1-port) converter now attached to ttyUSB0
Sun Dec 11 22:31:20 2022 kern.info kernel: [ 15.308859] option 2-1:1.1: GSM modem (1-port) converter detected
Sun Dec 11 22:31:20 2022 kern.info kernel: [ 15.315612] usb 2-1: GSM modem (1-port) converter now attached to ttyUSB1
Sun Dec 11 22:31:20 2022 kern.info kernel: [ 15.321466] option 2-1:1.2: GSM modem (1-port) converter detected
Sun Dec 11 22:31:20 2022 kern.info kernel: [ 15.328508] usb 2-1: GSM modem (1-port) converter now attached to ttyUSB2
Sun Dec 11 22:31:20 2022 kern.info kernel: [ 15.334318] option 2-1:1.3: GSM modem (1-port) converter detected
Sun Dec 11 22:31:20 2022 kern.info kernel: [ 15.341297] usb 2-1: GSM modem (1-port) converter now attached to ttyUSB3
Sun Dec 11 22:31:20 2022 kern.err kernel: [ 20.354430] ath11k c000000.wifi: Not multipd architecture
Sun Dec 11 22:31:20 2022 kern.info kernel: [ 20.354849] ath11k c000000.wifi: ipq6018 hw1.0
Sun Dec 11 22:31:20 2022 kern.info kernel: [ 20.359101] remoteproc remoteproc0: powering up cd00000.qcom_q6v5_wcss

–

BUT neither the gl-inet GUI detects it nor a new interface has been created.
So, I guess it is still unsupported (without manual changes), please confirm.

Thanks.

alzhao · 2022-12-12T04:50:19.872Z

I am using the exact modem and it works well.
Do you use a USB 3.0 hub?

image1125×497 31.8 KB

i7bar · 2022-12-12T20:24:35.822Z

Oh, this is very interesting. I am using a self powered USB 3 enclosure which works just fine with other routers.
Could you please do the following:
a) what is the version of AXT1800 firmware?

b) Can you press “Manual Setup” and show me a screenshot of the parameters defining protocol / port?

c) I assume you run the modem in QMI mode? Could you go to

http://YOU_MODEM_IP/#/modemmanage

run the following manual command: AT+QCFG="usbnet"

and show the screenshot with the command output?

d) can you please open luci and show the screenshot of the “Interface” page (want to see the name of WWAN interface, I have to create it manually).

e) can you please open the corresponding WWAN (LTE modem interface, whatever name it can have) and show me a screenshot with the general settings of the LTE interface (want to see protocol / device name)?

–
Last but not least - are you sure that you run your modem on the stock firmware and did not install any additional packages (I see that you work for GL.iNet and therefore your router could be used for tests, .i.e. some additional packages could be installed in the past)?

Thanks!

alzhao · 2022-12-13T11:13:51.418Z

Maybe it is the firmware version.

I am using a firmware that compiled internally. I forgot this info. Let me check with developers about firmware and modem support.

But here are some secreenshot for you.

image951×533 18.2 KB

image778×580 29.3 KB

alzhao · 2022-12-14T02:08:18.322Z

Checked again. 4.1.0 release 7 support this modem.

Also from your log, the modem is supported.

Can you check if you have all the ttyUSB device in /dev/?

Also did you change anything on the modem?

i7bar · 2022-12-14T02:33:40.798Z

alzhao:

Also from your log, the modem is supported.
Can you check if you have all the ttyUSB device in /dev/?
Also did you change anything on the modem?

I wrote in my initial post: “the modem was detected (info in the log), but neither the gl-inet GUI detects it nor a new interface has been created.”

I can make it work if I manually create the proper interface and assign to it the correct device (it will be /dev/cdc-wdm0 in case of QMI or /dev/ttyUSB2 or /dev/USB3 in case of UTMS) but this not what users have to do.

Can you please provide the rest of information I requested (d, e) ?

Thanks.

lizh · 2022-12-14T03:33:21.069Z

Can you provide the ID of the device? It can be viewed through ‘lsusb’.

i7bar · 2022-12-14T04:29:46.071Z

root@GL-AXT1800:~$ lsusb
Bus 001 Device 001: ID 1d6b:0002 Linux 4.4.60 xhci-hcd xHCI Host Controller
Bus 002 Device 002: ID 2c7c:0620 Quectel EM160R-GL
Bus 002 Device 001: ID 1d6b:0003 Linux 4.4.60 xhci-hcd xHCI Host Controller

gl1679×1188 249 KB

The connection is set, I can control the modem via luci but gl GUI does not show the modem info, it says " NO MODEM DEVICE FOUND".

This is the 4th time when I am trying to get the answer to a very simple question - WHAT IS THE NAME OF WWAN INTERFACE THAT HAS TO BE CREATED BY GL AFTER THE MODEM HAS BEEN DETECTED BY GL SOFT?

Thanks

alzhao · 2022-12-14T06:46:57.907Z

As long as you have ttyUSBx and cdc-wdm0 the modem should be displayed.

lizh · 2022-12-14T07:47:11.153Z

You can bind to the cloud platform to share with me, I will check the specific situation remotely.

My account is ‘zhangli’.

i7bar · 2022-12-15T01:43:52.819Z

I re-uploaded the latest firmware, reset the settings. I bound the device to a new account opened on goodcloud and shared it with your account. Right now the router works in repeater mode, the modem is attached and detected (the records in the log) but cannot be seen in GL GUI.

gl21682×1332 236 KB

But if you jump straight to

http://192.168.8.1/#/modemmanage

you will see that the modem is alive and connected:

gl11326×1296 128 KB

The name of APN to use: h2g2, no authentication.

lizh · 2022-12-15T09:03:45.695Z

Hi i7bar:

Thank you very much for your feedback.

Maybe this modem or sim card is special,So some information about the sim card cannot be obtained. As a result, the web page is not displayed.
We will accommodate this special case.

lizh · 2022-12-15T10:36:19.197Z

I temporarily updated a few packages. It should now display normally.

However, since mcc/mnc cannot be obtained, you need to fill in the APN by yourself.