i have router GL AR300 and a web camera logitech C310. webcam working perfect with original GLinet firmware at first but suddenly no picture at GL.inet interface.
reset was done but no luck. i think no problem with webcam because had been tested On PC and no problem.
thanks for help
Hi,
i think “yes”. they are default GL.inet ar300 firmware version 2.13
yes, please refer to attachment
dmesg
root@GL-AR300:~# dmesg
[ 0.000000] Linux version 3.10.49 (alzhao@alzhao-ubuntu) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r45620) ) #4 Wed Sep 23 10:53:49 HKT 2015
[ 0.000000] MyLoader: sysp=f38624f7, boardp=f68a8254, parts=29c0b996
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9344 rev 2
[ 0.000000] Clocks: CPU:560.000MHz, DDR:450.000MHz, AHB:225.000MHz, Ref:40.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] free_area_init_node: node 0, pgdat 80338b60, node_mem_map 81000000
[ 0.000000] Normal zone: 256 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: board=GL-AR300 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,16000k(firmware),64k(art)ro rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 126052k/131072k available (2386k kernel code, 5020k reserved, 620k data, 256k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.060000] Calibrating delay loop… 278.93 BogoMIPS (lpj=1394688)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 512
[ 0.080000] NET: Registered protocol family 16
[ 0.080000] MIPS: machine is GL AR300
[ 0.500000] bio: create slab <bio-0> at 0
[ 0.510000] Switching to clocksource MIPS
[ 0.510000] NET: Registered protocol family 2
[ 0.520000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.520000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.530000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.530000] TCP: reno registered
[ 0.540000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.540000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.550000] NET: Registered protocol family 1
[ 0.550000] PCI: CLS 0 bytes, default 32
[ 0.570000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.570000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.590000] msgmni has been set to 246
[ 0.590000] io scheduler noop registered
[ 0.590000] io scheduler deadline registered (default)
[ 0.600000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.630000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 0.640000] console [ttyS0] enabled, bootconsole disabled
[ 0.650000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[ 0.660000] m25p80 spi0.0: found w25q128, expected m25p80
[ 0.660000] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 0.670000] 4 cmdlinepart partitions found on MTD device spi0.0
[ 0.680000] Creating 4 MTD partitions on “spi0.0”:
[ 0.680000] 0x000000000000-0x000000040000 : “u-boot”
[ 0.690000] 0x000000040000-0x000000050000 : “u-boot-env”
[ 0.690000] 0x000000050000-0x000000ff0000 : “firmware”
[ 0.710000] 2 uimage-fw partitions found on MTD device firmware
[ 0.720000] 0x000000050000-0x000000170000 : “kernel”
[ 0.730000] 0x000000170000-0x000000ff0000 : “rootfs”
[ 0.730000] mtd: device 4 (rootfs) set to be root filesystem
[ 0.740000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.740000] 0x000000660000-0x000000ff0000 : “rootfs_data”
[ 0.750000] 0x000000ff0000-0x000001000000 : “art”
[ 0.770000] libphy: ag71xx_mdio: probed
[ 1.330000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY]
[ 1.340000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 1.890000] ag71xx-mdio.1: Found an AR934X built-in switch
[ 2.930000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 2.930000] TCP: cubic registered
[ 2.940000] NET: Registered protocol family 17
[ 2.940000] Bridge firewalling registered
[ 2.950000] 8021q: 802.1Q VLAN Support v1.8
[ 2.960000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 2.970000] Freeing unused kernel memory: 256K (80350000 - 80390000)
[ 6.030000] usbcore: registered new interface driver usbfs
[ 6.040000] usbcore: registered new interface driver hub
[ 6.040000] usbcore: registered new device driver usb
[ 6.090000] SCSI subsystem initialized
[ 6.100000] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
[ 6.100000] ehci-platform: EHCI generic platform driver
[ 6.110000] ehci-platform ehci-platform: EHCI Host Controller
[ 6.110000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 6.120000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 6.150000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 6.150000] hub 1-0:1.0: USB hub found
[ 6.160000] hub 1-0:1.0: 1 port detected
[ 6.160000] ohci_hcd: USB 1.1 ‘Open’ Host Controller (OHCI) Driver
[ 6.170000] uhci_hcd: USB Universal Host Controller Interface driver
[ 6.180000] usbcore: registered new interface driver usb-storage
[ 6.600000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 6.820000] hub 1-1:1.0: USB hub found
[ 6.820000] hub 1-1:1.0: 4 ports detected
[ 7.110000] usb 1-1.1: new high-speed USB device number 3 using ehci-platform
[ 7.560000] usb 1-1.2: new high-speed USB device number 4 using ehci-platform
[ 7.690000] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 7.690000] scsi0 : usb-storage 1-1.2:1.0
[ 7.800000] usb 1-1.4: new high-speed USB device number 5 using ehci-platform
[ 7.930000] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[ 7.940000] scsi1 : usb-storage 1-1.4:1.0
[ 8.700000] scsi 0:0:0:0: Direct-Access JetFlash Transcend 16GB 1.00 PQ: 0 ANSI: 5
[ 8.710000] sd 0:0:0:0: [sda] 30867456 512-byte logical blocks: (15.8 GB/14.7 GiB)
[ 8.720000] sd 0:0:0:0: [sda] Write Protect is off
[ 8.720000] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
[ 8.720000] sd 0:0:0:0: [sda] Write cache: disabled, read cache: disabled, doesn’t support DPO or FUA
[ 8.730000] sda: sda1
[ 8.740000] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 8.940000] scsi 1:0:0:0: Direct-Access Multi Flash Reader 1.00 PQ: 0 ANSI: 0
[ 8.950000] sd 1:0:0:0: [sdb] Attached SCSI removable disk
[ 9.870000] jffs2: notice: (378) jffs2_build_xattr_subsystem: complete building xattr subsystem, 20 of xdatum (1 unchecked, 19 orphan) and 87 of xref (0 dead, 67 orphan) found.
[ 14.900000] NET: Registered protocol family 10
[ 14.930000] NTFS driver 2.1.30 [Flags: R/O MODULE].
[ 14.970000] nf_conntrack version 0.5.0 (1973 buckets, 7892 max)
[ 14.990000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 15.030000] Linux video capture interface: v2.00
[ 15.070000] u32 classifier
[ 15.070000] input device check on
[ 15.080000] Actions configured
[ 15.090000] Mirror/redirect action on
[ 15.110000] fuse init (API version 7.22)
[ 15.130000] usbcore: registered new interface driver cdc_acm
[ 15.140000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 15.150000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[ 15.150000] Backport generated by backports.git backports-20140320-37-g5c33da0
[ 15.170000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 15.250000] usbcore: registered new interface driver usbserial
[ 15.250000] usbcore: registered new interface driver usbserial_generic
[ 15.260000] usbserial: USB Serial support registered for generic
[ 15.290000] uvcvideo: Found UVC 1.00 device <unnamed> (046d:081b)
[ 15.320000] input: UVC Camera (046d:081b) as /devices/platform/ehci-platform/usb1/1-1/1-1.1/1-1.1:1.0/input/input0
[ 15.340000] usbcore: registered new interface driver uvcvideo
[ 15.340000] USB Video Class driver (1.1.1)
[ 15.400000] xt_time: kernel timezone is -0000
[ 15.420000] usbcore: registered new interface driver cdc_ether
[ 15.480000] cfg80211: Calling CRDA to update world regulatory domain
[ 15.480000] cfg80211: World regulatory domain updated:
[ 15.490000] cfg80211: DFS Master region: unset
[ 15.490000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 15.500000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 15.510000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 15.520000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 15.530000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[ 15.540000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 15.550000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 15.550000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 15.560000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 15.570000] usbcore: registered new interface driver cp210x
[ 15.590000] usbserial: USB Serial support registered for cp210x
[ 15.610000] gspca_main: v2.14.0 registered
[ 15.610000] usbcore: registered new interface driver sonixb
[ 15.630000] usbcore: registered new interface driver sonixj
[ 15.650000] usbcore: registered new interface driver gspca_zc3xx
[ 15.720000] PPP generic driver version 2.4.2
[ 15.740000] NET: Registered protocol family 24
[ 15.750000] usbcore: registered new interface driver rndis_host
[ 15.830000] usbcore: registered new interface driver option
[ 15.850000] usbserial: USB Serial support registered for GSM modem (1-port)
[ 15.890000] usbcore: registered new interface driver rt2800usb
[ 15.920000] ath: EEPROM regdomain: 0x0
[ 15.920000] ath: EEPROM indicates default country code should be used
[ 15.920000] ath: doing EEPROM country->regdmn map search
[ 15.920000] ath: country maps to regdmn code: 0x3a
[ 15.920000] ath: Country alpha2 being used: US
[ 15.920000] ath: Regpair used: 0x3a
[ 15.950000] ieee80211 phy0: Selected rate control algorithm ‘minstrel_ht’
[ 15.950000] cfg80211: Calling CRDA for country: US
[ 15.960000] cfg80211: Regulatory domain changed to country: US
[ 15.960000] cfg80211: DFS Master region: FCC
[ 15.970000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 15.980000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[ 15.980000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
[ 15.990000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
[ 16.000000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 16.010000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 16.020000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=47
[ 22.270000] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 28.220000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 28.220000] device eth1 entered promiscuous mode
[ 28.250000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 28.280000] IPv6: ADDRCONF(NETDEV_UP): eth1.1: link is not ready
[ 28.310000] IPv6: ADDRCONF(NETDEV_UP): eth1.10: link is not ready
[ 28.340000] IPv6: ADDRCONF(NETDEV_UP): eth1.2: link is not ready
[ 28.370000] IPv6: ADDRCONF(NETDEV_UP): eth1.3: link is not ready
[ 32.570000] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready
[ 32.580000] device wlan0-1 entered promiscuous mode
[ 34.610000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 36.880000] wlan0: authenticate with 04:18:d6:cd:77:ce
[ 36.890000] wlan0: send auth to 04:18:d6:cd:77:ce (try 1/3)
[ 36.900000] wlan0: authenticated
[ 36.920000] wlan0: associate with 04:18:d6:cd:77:ce (try 1/3)
[ 36.920000] wlan0: RX AssocResp from 04:18:d6:cd:77:ce (capab=0x431 status=0 aid=1)
[ 36.930000] wlan0: associated
[ 36.940000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 38.810000] br-lan: port 2(wlan0-1) entered forwarding state
[ 38.820000] br-lan: port 2(wlan0-1) entered forwarding state
[ 38.820000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
[ 38.850000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 40.820000] br-lan: port 2(wlan0-1) entered forwarding state
The log seems fine! You are fulling utilizing the device: storage, camera, repeater …
Now I think it is the problem of mjpg-streamer or firewall.
#1 ps-w
root@GL-AR300:~# ps -w
PID USER VSZ STAT COMMAND
1 root 1396 S /sbin/procd
2 root 0 SW [kthreadd]
3 root 0 SW [ksoftirqd/0]
5 root 0 SW< [kworker/0:0H]
7 root 0 SW< [khelper]
60 root 0 SW< [writeback]
63 root 0 SW< [bioset]
65 root 0 SW< [kblockd]
91 root 0 SW [kworker/0:1]
96 root 0 SW [kswapd0]
143 root 0 SW [fsnotify_mark]
174 root 0 SW< [ath79-spi]
259 root 0 SW< [deferwq]
271 root 0 SW [khubd]
286 root 0 SW [kworker/u2:2]
340 root 0 SW [scsi_eh_0]
341 root 0 SW [usb-storage]
348 root 0 SW [scsi_eh_1]
349 root 0 SW [usb-storage]
356 root 0 SW< [kworker/0:1H]
379 root 0 SWN [jffs2_gcd_mtd5]
450 root 884 S /sbin/ubusd
453 root 772 S /sbin/askfirst ttyS0 /bin/ash --login
920 root 0 SW< [cfg80211]
1107 root 1036 S /sbin/logd -S 16
1156 root 1544 S /sbin/netifd
1190 root 1160 S /usr/sbin/odhcpd
1234 root 0 SW [jbd2/sda1-8]
1236 root 0 SW< [ext4-dio-unwrit]
1258 root 1152 S /usr/sbin/dropbear -F -P /var/run/dropbear.1.pid -p 22 -K 300
1271 root 3764 S /usr/sbin/lighttpd -f /etc/lighttpd/lighttpd.conf
1280 root 1472 S /www/cgi-bin/download_file
1291 root 5740 S /usr/bin/mjpg_streamer -i input_uvc.so -d /dev/video0 \ -f 25 -r 160x120 -o o
1615 root 1600 S /usr/sbin/hostapd -P /var/run/wifi-phy0.pid -B /var/run/hostapd-phy0.conf
1665 root 2464 S /usr/sbin/smbd -D
1669 root 2560 S /usr/sbin/nmbd -D
1765 root 1532 S /usr/sbin/wpa_supplicant -B -P /var/run/wpa_supplicant-wlan0.pid -D nl80211 -i wlan0 -c /var/run/wpa_supp
1827 root 1504 S /usr/sbin/uhttpd -f -h /www -r GL-AR300 -x /cgi-bin -u /ubus -t 60 -T 30 -k 20 -A 1 -n 3 -N 100 -R -p 0.0
1854 root 1372 S udhcpc -p /var/run/udhcpc-wlan0.pid -s /lib/netifd/dhcp.script -f -t 0 -i wlan0 -C
1912 root 1388 S {glautoupdater} /bin/sh /usr/bin/glautoupdater
1920 root 1364 S sleep 10800
2248 root 12096 S /usr/bin/transmission-daemon -g /mnt/sda1/config
2269 root 1376 S /usr/sbin/ntpd -n -p 0.openwrt.pool.ntp.org -p 1.openwrt.pool.ntp.org -p 2.openwrt.pool.ntp.org -p 3.open
2285 nobody 928 S /usr/sbin/dnsmasq -C /var/etc/dnsmasq.conf -k
2886 root 1436 S {glddnsupdater.s} /bin/sh /usr/lib/ddns/glddnsupdater.sh
2971 root 1116 S /usr/sbin/miniupnpd -f /var/etc/miniupnpd.conf
3038 root 0 SW [kworker/0:0]
3039 root 0 SW [kworker/u2:0]
3317 root 1364 S sleep 600
3336 root 0 SW [kworker/0:2]
3337 root 0 SW [kworker/u2:1]
3344 root 1220 S /usr/sbin/dropbear -F -P /var/run/dropbear.1.pid -p 22 -K 300
3345 root 1376 S -ash
3350 root 1372 R ps -w
seems mjpg streamer working fine then i wrote “/etc/init.d/mjpg-streamer restart” then
2# ps -w
root@GL-AR300:~# ps -w
PID USER VSZ STAT COMMAND
1 root 1396 S /sbin/procd
2 root 0 SW [kthreadd]
3 root 0 SW [ksoftirqd/0]
5 root 0 SW< [kworker/0:0H]
7 root 0 SW< [khelper]
60 root 0 SW< [writeback]
63 root 0 SW< [bioset]
65 root 0 SW< [kblockd]
91 root 0 SW [kworker/0:1]
96 root 0 SW [kswapd0]
143 root 0 SW [fsnotify_mark]
174 root 0 SW< [ath79-spi]
259 root 0 SW< [deferwq]
271 root 0 SW [khubd]
286 root 0 SW [kworker/u2:2]
340 root 0 SW [scsi_eh_0]
341 root 0 SW [usb-storage]
348 root 0 SW [scsi_eh_1]
349 root 0 SW [usb-storage]
356 root 0 SW< [kworker/0:1H]
379 root 0 SWN [jffs2_gcd_mtd5]
450 root 884 S /sbin/ubusd
453 root 772 S /sbin/askfirst ttyS0 /bin/ash --login
920 root 0 SW< [cfg80211]
1107 root 1036 S /sbin/logd -S 16
1156 root 1544 S /sbin/netifd
1190 root 1160 S /usr/sbin/odhcpd
1234 root 0 SW [jbd2/sda1-8]
1236 root 0 SW< [ext4-dio-unwrit]
1258 root 1152 S /usr/sbin/dropbear -F -P /var/run/dropbear.1.pid -p 22 -K 300
1271 root 3764 S /usr/sbin/lighttpd -f /etc/lighttpd/lighttpd.conf
1280 root 1472 S /www/cgi-bin/download_file
1615 root 1600 S /usr/sbin/hostapd -P /var/run/wifi-phy0.pid -B /var/run/hostapd-phy0.conf
1665 root 2464 S /usr/sbin/smbd -D
1669 root 2560 S /usr/sbin/nmbd -D
1765 root 1532 S /usr/sbin/wpa_supplicant -B -P /var/run/wpa_supplicant-wlan0.pid -D nl80211 -i wlan0 -c /var/run/wpa_supp
1827 root 1504 S /usr/sbin/uhttpd -f -h /www -r GL-AR300 -x /cgi-bin -u /ubus -t 60 -T 30 -k 20 -A 1 -n 3 -N 100 -R -p 0.0
1854 root 1372 S udhcpc -p /var/run/udhcpc-wlan0.pid -s /lib/netifd/dhcp.script -f -t 0 -i wlan0 -C
1912 root 1388 S {glautoupdater} /bin/sh /usr/bin/glautoupdater
1920 root 1364 S sleep 10800
2248 root 12096 S /usr/bin/transmission-daemon -g /mnt/sda1/config
2269 root 1376 S /usr/sbin/ntpd -n -p 0.openwrt.pool.ntp.org -p 1.openwrt.pool.ntp.org -p 2.openwrt.pool.ntp.org -p 3.open
2285 nobody 928 S /usr/sbin/dnsmasq -C /var/etc/dnsmasq.conf -k
2886 root 1436 S {glddnsupdater.s} /bin/sh /usr/lib/ddns/glddnsupdater.sh
2971 root 1116 S /usr/sbin/miniupnpd -f /var/etc/miniupnpd.conf
3038 root 0 SW [kworker/0:0]
3039 root 0 SW [kworker/u2:0]
3317 root 1364 S sleep 600
3336 root 0 SW [kworker/0:2]
3337 root 0 SW [kworker/u2:1]
3344 root 1220 S /usr/sbin/dropbear -F -P /var/run/dropbear.1.pid -p 22 -K 300
3345 root 1384 S -ash
3366 root 1372 R ps -w
now mjpg-streamer totally disappear
when you restart mjpg-streamer, did you see some output? if not, do a “dmesg” immediately to show if there is some message. Please post output.
seems mjpg-streamer process is ok right now. maybe just little bit lag. but still no luck with cam
Change resolution and try again.
It’s advisible to try some different mainly used video resolutions like 320x240, 640x480, 1280x102, 1280x720, etc.
When I try my Mini UVC webcam from GLi at a resolution of 1024x768 for example I got crambled images or even no output because the combination of UVC drivers and the supported for it within the webcam is not always ideal.
The supported resolutions of the Mini UVC webcam from GLi can be found at the webshop page: 404 Page not found - GL.iNet I can confirm the resolutions mentioned there are indeed the only correct working ones.
This poage can be handy to determine which resolutions are supported by which webcams on Linux: RPi USB Webcams - eLinux.org
As you can see the Logitech C310 should work, but there are no confirmed correct working resolutions.