Firmware 3.105 Snapshot Update

temerosoivan · December 11, 2020, 3:44am

When I upgrade to 3.105 on my mifi, I can’t connect to LTE. I am not using the quectel module. I am using a Fobicom module. It was working fine with 3.029. I see this error in the logs.

Mon Dec 7 07:42:40 2020 daemon.notice netifd: Interface ‘modem_1_1_2’ is now down
Mon Dec 7 07:42:40 2020 daemon.notice netifd: Interface ‘modem_1_1_2’ is setting up now
Mon Dec 7 07:42:44 2020 daemon.notice netifd: modem_1_1_2 (9882): find: -name requires an argument
Mon Dec 7 07:42:44 2020 daemon.notice netifd: modem_1_1_2 (9882): cat: can’t open ‘/tmp/modem./signal’: No such file or directory
Mon Dec 7 07:42:45 2020 daemon.notice netifd: modem_1_1_2 (10085): /usr/sbin/pppd: unrecognized option ‘/dev’
Mon Dec 7 07:42:45 2020 daemon.err pppd[10085]: unrecognized option ‘/dev’
Mon Dec 7 07:42:45 2020 daemon.notice netifd: modem_1_1_2 (10085): pppd version 2.4.7
Mon Dec 7 07:42:45 2020 daemon.notice netifd: modem_1_1_2 (10085): Usage: /usr/sbin/pppd [ options ], where options are:
Mon Dec 7 07:42:45 2020 daemon.notice netifd: modem_1_1_2 (10085): Communicate over the named device
Mon Dec 7 07:42:45 2020 daemon.notice netifd: modem_1_1_2 (10085): Set the baud rate to
Mon Dec 7 07:42:45 2020 daemon.notice netifd: modem_1_1_2 (10085): : Set the local and/or remote interface IP
Mon Dec 7 07:42:45 2020 daemon.notice netifd: modem_1_1_2 (10085): addresses. Either one may be omitted.
Mon Dec 7 07:42:45 2020 daemon.notice netifd: modem_1_1_2 (10085): asyncmap Set the desired async map to hex
Mon Dec 7 07:42:45 2020 daemon.notice netifd: modem_1_1_2 (10085): auth Require authentication from peer
Mon Dec 7 07:42:45 2020 daemon.notice netifd: modem_1_1_2 (10085): connect

Invoke shell command

to set up the serial line
Mon Dec 7 07:42:45 2020 daemon.notice netifd: modem_1_1_2 (10085): crtscts Use hardware RTS/CTS flow control
Mon Dec 7 07:42:45 2020 daemon.notice netifd: modem_1_1_2 (10085): defaultroute Add default route through interface
Mon Dec 7 07:42:45 2020 daemon.notice netifd: modem_1_1_2 (10085): file Take options from file
Mon Dec 7 07:42:45 2020 daemon.notice netifd: modem_1_1_2 (10085): modem Use modem control lines
Mon Dec 7 07:42:45 2020 daemon.notice netifd: modem_1_1_2 (10085): mru Set MRU value to for negotiation

alzhao · December 11, 2020, 4:15am

can you show screenshot of the the modem config UI?

temerosoivan · December 12, 2020, 10:26pm

I have rollbacked the upgrade. But basically device is /dev/ttyACM0 and I set an APN and dial number is *99#. Mode is LTE and proto is auto.

zakaria · December 14, 2020, 10:24am

I installed the upgrade but I can’t install kmod-fs-f2fs

root@GL-AR750S:~# opkg install kmod-fs-f2fs
Installing kmod-fs-f2fs (4.9.120-1) to root...
Downloading https://fw.gl-inet.com/releases/kmod-3.4/ar71xx/nand/kmod-fs-f2fs_4.9.120-1_mips_24kc.ipk
Collected errors:
 * opkg_install_pkg: Package size mismatch: kmod-fs-f2fs is 116332 bytes, expecting 116328 bytes
 * opkg_install_cmd: Cannot install package kmod-fs-f2fs.

radishman · December 15, 2020, 4:13am

Has been fixed,please do opkg update and try again.

Crafuntyo · December 16, 2020, 7:23am

I am running a snapshot of 3.105 so the actual 3.105 release is not detected, having the same version number.
How can I upgrade it then? On the official page I could only find the u-boot images, but I’d rather not use that.

There is a “release” folder for AR750S
http://download.gl-inet.com/firmware/ar750s/release/

But not for the AR-300M!
http://download.gl-inet.com/firmware/ar300m/

Thank you,

alzhao · December 16, 2020, 8:05am

It is here http://download.gl-inet.com/firmware/ar300m/nand/v1/

Crafuntyo · December 16, 2020, 8:19am

Thank you @alzhao. I think the directories in the download site should be more consistent for the benefits of the users.

Many thanks,

alzhao · December 16, 2020, 8:24am

AR300M has two firmware and this is a legacy issue cannot changed.

bOcy · December 18, 2020, 5:17pm

mango 3.105: wireguard vpn is not using specified dns, so unable to resolve at all, unless enabled cloudflare in ‘custom dns’

compared to gl-ap1300lte which is working

agent_smith · December 18, 2020, 6:51pm

In the release notes V3.105 for Slate is support of russian language. I have updated my Slate to 1.05 with last release. There is no russian language.
Did I do something wrong or misunderstood?
Thank you in advance!

osakanataro · December 21, 2020, 8:02am

GL-MV1000 v3.105 and v3.104 is not work IPv6.
(v3.102 is worked IPv6)

alzhao · December 21, 2020, 10:16am

It is firmware problem. Need to add asap.

modumb · December 21, 2020, 10:17am

Hi… I can’t remember if I updated from the beta to the release version. Can someone please confirm that the compile time here corresponds with the 3.105 final release?

[I have the gl ar750s]

alzhao · December 21, 2020, 10:19am

Yes, 2020-12-17 is correct.

osakanataro · December 21, 2020, 12:41pm

yes, 3.105 final release.
Update from this GUI.

3zzy · December 30, 2020, 4:11am

I’m using Wireguard with policy enabled and looks like its causing frequent dropouts. Is it a known issue?

robo · January 10, 2021, 5:15pm

USB150
After upgrading to 3.105 gui works so slow. Before upgrade gui worked well.
Now using router is a little frustrating.
Could you please fix it?

asdffdsa1122 · January 10, 2021, 5:37pm

same with my usb150

old firmware no problems.

new firmware,
gui is not usable now, so slow and constant timeouts.

Predators46 · January 24, 2021, 12:03am

when will this be available in the stable version