Yes. We are testing this and will put this function in our standard firmware once done.
4 Likes
Please remove the “Modem Reset” at the main “Internet > Modem” panel. Everytime I go to click “AT Commands” or “Cells Info” I click it by accident and it takes long when my modem resets.
Also change the “Cells info” to match the tower info from Cellmapper"
2 Likes
It would not be bad to see an analogue of VPN policies for Tor
Tor via VPN, VPN via Tor
1 Like
Sorry for the dup post but I found the official feature request thread after my previous post.
I think a killer feature that no one else has, is the option to proxy via the router configuration page to a captive portal via an iframe (or some other mechanism like a remote renderer on an HTML5 canvas… maybe flutter for web can do something here).
If you google all of the pain and multiple steps required for captive portals (mess with dns, etc), and since the primary use/case is a travel router, this would make a lot of people’s lives much easier.
I mean, it’s at least half a dozen steps jumping across multiple screens and devices when I use my 750 to deal with hotel captive portals.
No one else has this and with the growing awareness of how evil public wifi is, I think the more usable you can make this, the more likelihood you could get much larger adoption of your products.
5 Likes
When looking at the ‘Cells Info’ of the Mobile Network Connection, if the Signal Status is ‘Good’ it is shown in a Yellow that is very hard to read against the white background of the page.
Could the shade be changed slightly to make it more readable?
1 Like
A must: 
Adding a checkbox to enable/disable SIP ALG. This would avoid having to go in the kernel and manually edit files to allow VOIP traffic to run over the router (refer to discussion [Disable/Enable SIP ALG]
3 Likes
I think it would be cool to see mobile 5G GL.iNet devices, perhaps with WiFi 6
2 Likes
On “Clients” page, I like the switch that turns Blocks an IP address BUT,…
I want 2 CheckBox 
… to “Block WAN” and/or “Block LAN”
EDIT:
I also want ability to change Name of device (I HATE the nameless * or some annoying names set on various devices)
Don’t suggest me LuCi (because I will take that as “go to hell”) 
Change name will be there. But why two checkbox?
One Checkbox to Block access to LAN only and another to Block access to WAN only (internet)
If both Checkbox is enabled, client is will be blocked completely
Some devices like printers automatically connect to internet (send user analytics to their company without user knowledge)
Some devices which are meant to access internet only, query around and disturb other devices (again without user knowledge)
“isolate clients” would be useful also so that clients will not be able to interact with other clients, it’s available in luci with some models, would be great to add into the glinet admin panel.
My request for two checkbox serves this purpose of “isolate clients” already. If “Block LAN” is ON while “Block WAN” is OFF, client is already considered isolated and can only access internet
edit: on “Clients” page, the Title above switches is “Block” only,…
Over there, I want “Block LAN | Block WAN” as title and below the title, I want CheckBoxes that turns ON or OFF the function
1 Like
I feel there should be a button in the main GL iNet GUI that collects debug information and then either produces a zipped or gzipped tar file that can be downloaded from the router to the user’s PC using the GUI.
After several years of reading this forum, I keep seeing requests for debug information, like the output of dmesg, logread, wg, ps, top, ip addr, ip link, config file information, … . This is normally followed by an explanation on how to use ssh to gather this information and then how to transfer the information to a PC so it can be sent to support. Why not just make it real simple to gather up all the debug information and put in on the user’s PC so they can submit it.
Using regular expressions and sed, you could even filter out information like IP address and Wireguard keys.
3 Likes
In firmware 4.x you can export the log from the UI with a .zip now.
1 Like
It would be nice to see the connection uptime on the main screen of the router.
2 Likes
SQM cake fq_codel or nss schedulers should be installed by default along with QoS. Also custom firewall rules too is needed.
Can this SOC be integrated? Plz n thank u
1 Like
We have a list of Quectel 5G modules under consideration now. Hope to add support
2 Likes
FIREWALL Page must have
- “Blocklist” and
- “Block Country” (specially if you will allow WebDAV or inward connections).
Blocklist can contain list of known attackers
(user can upload from URL or Local file)
Block Country can contain IP address range allocated by countries (User can Check to block countries)
3 Likes
I want an option to “Reboot into Uboot mode” from Admin Panel (because I hate going behind router and mess with Reset buttons) 
This option can go into
MORE SETTINGS > Revert Firmwares Page,
Or
UPGRADE Page
AND Also,… I prefer Uboot allowing Full BackUp/Restores to USB or NAS 
3 Likes