Occasional crash on standard repeater or luci channel analysis

TapGhoul · January 20, 2024, 3:56pm

Hey! When starting a scan for APs when enabling repeater, or when going to Luci and doing a channel analysis, the entire router sometimes crashes (and if not, just returns no values in the case of repeater)

I have tried factory resetting it, and it still breaks. Note, in all cases, wifi modes are set to 5ghz 11n/ac/ax with channel fixed at 161, and 2.4ghz 11n/ax with channel set to 11. The crash log mentioned I was also doing tethering from a phone, but this seems to be an issue regardless of tethering or not, and does not have an effect over whether it crashes vs just fails.

I am connected over wifi while this happens, so the expectation is to see a disconnect + reconnect here.

Note the crash does not always happen - when it doesn’t crash, channel analysis works fine, but the repeater AP scan still shows no entries.

Model: GL.iNet GL-MT6000
Firmware version: 4.5.5
Firmware type: release3
OpenWRT version: OpenWrt 23.05-SNAPSHOT r23001+719-38c150612c
Kernel version: 5.15.139

Oops#1 Part1
<6>[   15.142016] br-lan: port 5(lan5) entered blocking state
<6>[   15.147236] br-lan: port 5(lan5) entered disabled state
<6>[   15.154604] device lan5 entered promiscuous mode
<6>[   15.487770] mtk_soc_eth 15100000.ethernet eth1: PHY [mdio-bus:01] driver [RTL8221B-VB-CG 2.5Gbps PHY] (irq=62)
<6>[   15.498023] mtk_soc_eth 15100000.ethernet eth1: configuring for phy/2500base-x link mode
<6>[   16.216717] br-lan: port 6(wlan0) entered blocking state
<6>[   16.222112] br-lan: port 6(wlan0) entered disabled state
<6>[   16.227668] device wlan0 entered promiscuous mode
<6>[   16.288563] device wlan0 left promiscuous mode
<6>[   16.293098] br-lan: port 6(wlan0) entered disabled state
<6>[   16.373345] mt7530-mdio mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
<6>[   16.419841] br-lan: port 1(lan1) entered blocking state
<6>[   16.425081] br-lan: port 1(lan1) entered forwarding state
<6>[   16.472664] br-lan: port 6(wlan0) entered blocking state
<6>[   16.478000] br-lan: port 6(wlan0) entered disabled state
<6>[   16.483531] device wlan0 entered promiscuous mode
<6>[   16.488461] br-lan: port 6(wlan0) entered blocking state
<6>[   16.493795] br-lan: port 6(wlan0) entered forwarding state
<6>[   16.653594] br-lan: port 6(wlan0) entered disabled state
<6>[   16.716596] tertf: br-lan registered, add it
<6>[   16.723354] br-lan: port 7(wlan1) entered blocking state
<6>[   16.728734] br-lan: port 7(wlan1) entered disabled state
<6>[   16.734289] device wlan1 entered promiscuous mode
<6>[   16.788442] device wlan1 left promiscuous mode
<6>[   16.793015] br-lan: port 7(wlan1) entered disabled state
<6>[   16.977290] br-lan: port 7(wlan1) entered blocking state
<6>[   16.982645] br-lan: port 7(wlan1) entered disabled state
<6>[   16.988174] device wlan1 entered promiscuous mode
<6>[   16.993031] br-lan: port 7(wlan1) entered blocking state
<6>[   16.998362] br-lan: port 7(wlan1) entered forwarding state
<6>[   17.700346] br-lan: port 7(wlan1) entered disabled state
<6>[   17.944422] br-lan: port 7(wlan1) entered blocking state
<6>[   17.949776] br-lan: port 7(wlan1) entered forwarding state
<6>[   18.087726] mt7530-mdio mdio-bus:1f lan3: Link is Up - 1Gbps/Full - flow control rx/tx
<6>[   18.095732] br-lan: port 3(lan3) entered blocking state
<6>[   18.100983] br-lan: port 3(lan3) entered forwarding state
<6>[   18.230083] mt7530-mdio mdio-bus:1f lan4: Link is Up - 1Gbps/Full - flow control rx/tx
<6>[   18.238057] br-lan: port 4(lan4) entered blocking state
<6>[   18.243289] br-lan: port 4(lan4) entered forwarding state
<7>[   19.379608] xt_FULLCONENAT: warning: failed to register a conntrack notifier. Disable active GC for mappings.
<6>[   27.301800] br-lan: port 6(wlan0) entered blocking state
<6>[   27.307117] br-lan: port 6(wlan0) entered forwarding state
<6>[   44.775013] usb 1-2: USB disconnect, device number 2
<6>[   45.427763] usb 1-2: new high-speed USB device number 3 using xhci-mtk
<6>[   45.615614] rndis_host 1-2:1.0 usb0: register 'rndis_host' at usb-11200000.usb-2, RNDIS device, 06:8d:71:ac:e7:ac
<7>[   46.764582] [add_dev_config 307]add node success. iface:tethering, dev:usb0, ifindex:14
<1>[  203.168669] Unable to handle kernel write to read-only memory at virtual address 0000000000000000
<1>[  203.177550] Mem abort info:
<1>[  203.180336]   ESR = 0x0000000096000045
<1>[  203.184081]   EC = 0x25: DABT (current EL), IL = 32 bits
<1>[  203.189379]   SET = 0, FnV = 0
<1>[  203.192422]   EA = 0, S1PTW = 0
<1>[  203.195548]   FSC = 0x05: level 1 translation fault
<1>[  203.200406] Data abort info:
<1>[  203.203274]   ISV = 0, ISS = 0x00000045
<1>[  203.207092]   CM = 0, WnR = 1
<1>[  203.210043] user pgtable: 4k pages, 39-bit VAs, pgdp=000000004a619000
<1>[  203.216467] [0000000000000000] pgd=0000000000000000, p4d=0000000000000000, pud=0000000000000000
<0>[  203.225149] Internal error: Oops: 0000000096000045 [#1] SMP
<7>[  203.230703] Modules linked in: xt_FULLCONENAT pppoe ppp_async option wireguard usb_wwan rndis_host qmi_wwan pppox ppp_generic nft_fib_inet nf_flow_table_ipv6 nf_flow_table_ipv4 nf_flow_table_inet mt7915e mt76_connac_lib mt76 mac80211 libchacha20poly1305 ipt_REJECT huawei_cdc_ncm chacha_neon cfg80211 cdc_ncm cdc_ether xt_time xt_tcpudp xt_state xt_recent xt_quota xt_pkttype xt_owner xt_nat xt_multiport xt_mark xt_mac xt_limit xt_helper xt_conntrack xt_connmark xt_connlimit xt_connbytes xt_comment xt_cgroup xt_addrtype xt_TCPMSS xt_REDIRECT xt_MASQUERADE xt_LOG xt_CT usbserial usbnet slhc poly1305_neon nft_reject_ipv6 nft_reject_ipv4 nft_reject_inet nft_reject nft_redir nft_quota nft_objref nft_numgen nft_nat nft_masq nft_log nft_limit nft_hash nft_flow_offload nft_fib_ipv6 nft_fib_ipv4 nft_fib nft_ct nft_counter nft_compat nft_chain_nat nf_tables nf_reject_ipv4 nf_log_syslog nf_flow_table nf_conntrack_netlink nf_conncount mdio_netlink libcurve25519_generic libcrc32c libchacha iptable_nat
<7>[  203.230842]  iptable_mangle iptable_filter ipheth ip_tables crc_ccitt compat cls_flower cdc_wdm cdc_acm br_netfilter arptable_filter arpt_mangle arp_tables act_vlan crypto_safexcel fuse cls_bpf act_bpf sch_tbf sch_ingress sch_htb sch_hfsc em_u32 cls_u32 cls_route cls_matchall cls_fw cls_flow cls_basic act_skbedit act_mirred act_gact xt_set ip_set_list_set ip_set_hash_netportnet ip_set_hash_netport ip_set_hash_netnet ip_set_hash_netiface ip_set_hash_net ip_set_hash_mac ip_set_hash_ipportnet ip_set_hash_ipportip ip_set_hash_ipport ip_set_hash_ipmark ip_set_hash_ipmac ip_set_hash_ip ip_set_bitmap_port ip_set_bitmap_ipmac ip_set_bitmap_ip ip_set nfnetlink ip6table_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ip6t_NPT ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 ifb ip6_udp_tunnel udp_tunnel tun ntfs nls_utf8 nls_iso8859_1 nls_cp437 sha1_generic seqiv md5 des_generic libdes authencesn authenc mtdoops uas usb_storage leds_gpio xhci_plat_hcd xhci_pci
<7>[  203.318165]  xhci_mtk_hcd xhci_hcd uhci_hcd ohci_platform ohci_hcd fsl_mph_dr_of ehci_platform ehci_fsl kmwan ehci_hcd gpio_button_hotplug gl_sdk4_tertf gl_sdk4_black_white_list vfat fat exfat usbcore usb_common mii gl_sdk4_hw_info
<7>[  203.425752] CPU: 1 PID: 387 Comm: napi/mtk_eth-6 Not tainted 5.15.139 #0
<7>[  203.432433] Hardware name: GL.iNet GL-MT6000 (DT)
<7>[  203.437118] pstate: 80400005 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
<7>[  203.444058] pc : mt76_tx+0xb8/0x630 [mt76]
<7>[  203.448152] lr : mt7915_eeprom_get_power_delta+0x1928/0x2580 [mt7915e]
<7>[  203.454665] sp : ffffffc0099d3400
<7>[  203.457963] x29: ffffffc0099d3400 x28: ffffff8005b69928 x27: ffffff8004d88d90
<7>[  203.465079] x26: ffffffc0099d35b0 x25: ffffff800a7c1958 x24: 0000000000000000
<7>[  203.472194] x23: ffffff8005b69928 x22: ffffffc000fdffa8 x21: ffffff8005b69900
<7>[  203.479310] x20: ffffff8004d8a020 x19: ffffff8005926cc8 x18: 0000000000000000
<7>[  203.486426] x17: 0000000000000a40 x16: ffffffc008f2b000 x15: 0000000000000520
<7>[  203.493542] x14: ffffffffffffd9f8 x13: 00000003aaaa0000 x12: 0000000000000000
<7>[  203.500657] x11: ffffff8001e1d560 x10: ffffff8001de9150 x9 : ffffff8001e1d540
<7>[  203.507772] x8 : 0000000042f6eb50 x7 : ffffff800c498100 x6 : 00000000f0000010
<7>[  203.514888] x5 : ffffff8004ee2020 x4 : 0000000000000000 x3 : 0000000000000001
<7>[  203.522002] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffffff8005926e00
<7>[  203.529119] Call trace:
<7>[  203.531551]  mt76_tx+0xb8/0x630 [mt76]
<7>[  203.535287]  mt7915_eeprom_get_power_delta+0x1928/0x2580 [mt7915e]
<7>[  203.541451]  __ieee80211_schedule_txq+0xe60/0x1b30 [mac80211]
<7>[  203.547206]  __ieee80211_xmit_fast+0x7b4/0x950 [mac80211]
<7>[  203.552600]  __ieee80211_subif_start_xmit+0x1e8/0x354 [mac80211]
<7>[  203.558603]  ieee80211_subif_start_xmit+0x3c/0x3bc [mac80211]
<7>[  203.564345]  ieee80211_subif_start_xmit_8023+0x318/0x430 [mac80211]
<7>[  203.570606]  dev_hard_start_xmit+0xe4/0x180
<7>[  203.574776]  __dev_queue_xmit+0x968/0xc30
<7>[  203.578769]  dev_queue_xmit+0x10/0x20
<7>[  203.582415]  br_dev_queue_push_xmit+0x9c/0x1b4
<7>[  203.586845]  br_forward_finish+0x98/0xb0
<7>[  203.590752]  __br_forward+0x138/0x1a0
<7>[  203.594399]  br_forward+0x124/0x150
<7>[  203.597873]  br_handle_frame_finish+0x30c/0x4d0
<7>[  203.602386]  br_handle_frame+0x398/0x41c
<7>[  203.606291]  __netif_receive_skb_core.constprop.0+0x254/0xcb0
<7>[  203.612018]  __netif_receive_skb_list_core+0xd4/0x1e0
<7>[  203.617050]  netif_receive_skb_list_internal+0x1b8/0x280
<7>[  203.622343]  napi_complete_done+0x64/0x1a0
<7>[  203.626423]  gro_cell_poll+0x80/0xa0
<7>[  203.629986]  __napi_poll+0x54/0x1b0
<7>[  203.633460]  net_rx_action+0x2a0/0x320
<7>[  203.637192]  _stext+0x10c/0x28c
<7>[  203.640320]  do_softirq+0x8c/0xa0
<7>[  203.643623]  __local_bh_enable_ip+0xa0/0xa4
<7>[  203.647789]  napi_threaded_poll+0x120/0x1a0
<7>[  203.651956]  kthread+0x11c/0x130
<7>[  203.655173]  ret_from_fork+0x10/0x20
<0>[  203.658735] Code: f90002a0 52800002 f90006a1 f900a275 (f9000035) 
<4>[  203.664808] ---[ end trace eb5248042cf7d915 ]---


Panic#2 Part1
<6>[   15.498023] mtk_soc_eth 15100000.ethernet eth1: configuring for phy/2500base-x link mode
<6>[   16.216717] br-lan: port 6(wlan0) entered blocking state
<6>[   16.222112] br-lan: port 6(wlan0) entered disabled state
<6>[   16.227668] device wlan0 entered promiscuous mode
<6>[   16.288563] device wlan0 left promiscuous mode
<6>[   16.293098] br-lan: port 6(wlan0) entered disabled state
<6>[   16.373345] mt7530-mdio mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
<6>[   16.419841] br-lan: port 1(lan1) entered blocking state
<6>[   16.425081] br-lan: port 1(lan1) entered forwarding state
<6>[   16.472664] br-lan: port 6(wlan0) entered blocking state
<6>[   16.478000] br-lan: port 6(wlan0) entered disabled state
<6>[   16.483531] device wlan0 entered promiscuous mode
<6>[   16.488461] br-lan: port 6(wlan0) entered blocking state
<6>[   16.493795] br-lan: port 6(wlan0) entered forwarding state
<6>[   16.653594] br-lan: port 6(wlan0) entered disabled state
<6>[   16.716596] tertf: br-lan registered, add it
<6>[   16.723354] br-lan: port 7(wlan1) entered blocking state
<6>[   16.728734] br-lan: port 7(wlan1) entered disabled state
<6>[   16.734289] device wlan1 entered promiscuous mode
<6>[   16.788442] device wlan1 left promiscuous mode
<6>[   16.793015] br-lan: port 7(wlan1) entered disabled state
<6>[   16.977290] br-lan: port 7(wlan1) entered blocking state
<6>[   16.982645] br-lan: port 7(wlan1) entered disabled state
<6>[   16.988174] device wlan1 entered promiscuous mode
<6>[   16.993031] br-lan: port 7(wlan1) entered blocking state
<6>[   16.998362] br-lan: port 7(wlan1) entered forwarding state
<6>[   17.700346] br-lan: port 7(wlan1) entered disabled state
<6>[   17.944422] br-lan: port 7(wlan1) entered blocking state
<6>[   17.949776] br-lan: port 7(wlan1) entered forwarding state
<6>[   18.087726] mt7530-mdio mdio-bus:1f lan3: Link is Up - 1Gbps/Full - flow control rx/tx
<6>[   18.095732] br-lan: port 3(lan3) entered blocking state
<6>[   18.100983] br-lan: port 3(lan3) entered forwarding state
<6>[   18.230083] mt7530-mdio mdio-bus:1f lan4: Link is Up - 1Gbps/Full - flow control rx/tx
<6>[   18.238057] br-lan: port 4(lan4) entered blocking state
<6>[   18.243289] br-lan: port 4(lan4) entered forwarding state
<7>[   19.379608] xt_FULLCONENAT: warning: failed to register a conntrack notifier. Disable active GC for mappings.
<6>[   27.301800] br-lan: port 6(wlan0) entered blocking state
<6>[   27.307117] br-lan: port 6(wlan0) entered forwarding state
<6>[   44.775013] usb 1-2: USB disconnect, device number 2
<6>[   45.427763] usb 1-2: new high-speed USB device number 3 using xhci-mtk
<6>[   45.615614] rndis_host 1-2:1.0 usb0: register 'rndis_host' at usb-11200000.usb-2, RNDIS device, 06:8d:71:ac:e7:ac
<7>[   46.764582] [add_dev_config 307]add node success. iface:tethering, dev:usb0, ifindex:14
<1>[  203.168669] Unable to handle kernel write to read-only memory at virtual address 0000000000000000
<1>[  203.177550] Mem abort info:
<1>[  203.180336]   ESR = 0x0000000096000045
<1>[  203.184081]   EC = 0x25: DABT (current EL), IL = 32 bits
<1>[  203.189379]   SET = 0, FnV = 0
<1>[  203.192422]   EA = 0, S1PTW = 0
<1>[  203.195548]   FSC = 0x05: level 1 translation fault
<1>[  203.200406] Data abort info:
<1>[  203.203274]   ISV = 0, ISS = 0x00000045
<1>[  203.207092]   CM = 0, WnR = 1
<1>[  203.210043] user pgtable: 4k pages, 39-bit VAs, pgdp=000000004a619000
<1>[  203.216467] [0000000000000000] pgd=0000000000000000, p4d=0000000000000000, pud=0000000000000000
<0>[  203.225149] Internal error: Oops: 0000000096000045 [#1] SMP
<7>[  203.230703] Modules linked in: xt_FULLCONENAT pppoe ppp_async option wireguard usb_wwan rndis_host qmi_wwan pppox ppp_generic nft_fib_inet nf_flow_table_ipv6 nf_flow_table_ipv4 nf_flow_table_inet mt7915e mt76_connac_lib mt76 mac80211 libchacha20poly1305 ipt_REJECT huawei_cdc_ncm chacha_neon cfg80211 cdc_ncm cdc_ether xt_time xt_tcpudp xt_state xt_recent xt_quota xt_pkttype xt_owner xt_nat xt_multiport xt_mark xt_mac xt_limit xt_helper xt_conntrack xt_connmark xt_connlimit xt_connbytes xt_comment xt_cgroup xt_addrtype xt_TCPMSS xt_REDIRECT xt_MASQUERADE xt_LOG xt_CT usbserial usbnet slhc poly1305_neon nft_reject_ipv6 nft_reject_ipv4 nft_reject_inet nft_reject nft_redir nft_quota nft_objref nft_numgen nft_nat nft_masq nft_log nft_limit nft_hash nft_flow_offload nft_fib_ipv6 nft_fib_ipv4 nft_fib nft_ct nft_counter nft_compat nft_chain_nat nf_tables nf_reject_ipv4 nf_log_syslog nf_flow_table nf_conntrack_netlink nf_conncount mdio_netlink libcurve25519_generic libcrc32c libchacha iptable_nat
<7>[  203.230842]  iptable_mangle iptable_filter ipheth ip_tables crc_ccitt compat cls_flower cdc_wdm cdc_acm br_netfilter arptable_filter arpt_mangle arp_tables act_vlan crypto_safexcel fuse cls_bpf act_bpf sch_tbf sch_ingress sch_htb sch_hfsc em_u32 cls_u32 cls_route cls_matchall cls_fw cls_flow cls_basic act_skbedit act_mirred act_gact xt_set ip_set_list_set ip_set_hash_netportnet ip_set_hash_netport ip_set_hash_netnet ip_set_hash_netiface ip_set_hash_net ip_set_hash_mac ip_set_hash_ipportnet ip_set_hash_ipportip ip_set_hash_ipport ip_set_hash_ipmark ip_set_hash_ipmac ip_set_hash_ip ip_set_bitmap_port ip_set_bitmap_ipmac ip_set_bitmap_ip ip_set nfnetlink ip6table_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ip6t_NPT ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 ifb ip6_udp_tunnel udp_tunnel tun ntfs nls_utf8 nls_iso8859_1 nls_cp437 sha1_generic seqiv md5 des_generic libdes authencesn authenc mtdoops uas usb_storage leds_gpio xhci_plat_hcd xhci_pci
<7>[  203.318165]  xhci_mtk_hcd xhci_hcd uhci_hcd ohci_platform ohci_hcd fsl_mph_dr_of ehci_platform ehci_fsl kmwan ehci_hcd gpio_button_hotplug gl_sdk4_tertf gl_sdk4_black_white_list vfat fat exfat usbcore usb_common mii gl_sdk4_hw_info
<7>[  203.425752] CPU: 1 PID: 387 Comm: napi/mtk_eth-6 Not tainted 5.15.139 #0
<7>[  203.432433] Hardware name: GL.iNet GL-MT6000 (DT)
<7>[  203.437118] pstate: 80400005 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
<7>[  203.444058] pc : mt76_tx+0xb8/0x630 [mt76]
<7>[  203.448152] lr : mt7915_eeprom_get_power_delta+0x1928/0x2580 [mt7915e]
<7>[  203.454665] sp : ffffffc0099d3400
<7>[  203.457963] x29: ffffffc0099d3400 x28: ffffff8005b69928 x27: ffffff8004d88d90
<7>[  203.465079] x26: ffffffc0099d35b0 x25: ffffff800a7c1958 x24: 0000000000000000
<7>[  203.472194] x23: ffffff8005b69928 x22: ffffffc000fdffa8 x21: ffffff8005b69900
<7>[  203.479310] x20: ffffff8004d8a020 x19: ffffff8005926cc8 x18: 0000000000000000
<7>[  203.486426] x17: 0000000000000a40 x16: ffffffc008f2b000 x15: 0000000000000520
<7>[  203.493542] x14: ffffffffffffd9f8 x13: 00000003aaaa0000 x12: 0000000000000000
<7>[  203.500657] x11: ffffff8001e1d560 x10: ffffff8001de9150 x9 : ffffff8001e1d540
<7>[  203.507772] x8 : 0000000042f6eb50 x7 : ffffff800c498100 x6 : 00000000f0000010
<7>[  203.514888] x5 : ffffff8004ee2020 x4 : 0000000000000000 x3 : 0000000000000001
<7>[  203.522002] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffffff8005926e00
<7>[  203.529119] Call trace:
<7>[  203.531551]  mt76_tx+0xb8/0x630 [mt76]
<7>[  203.535287]  mt7915_eeprom_get_power_delta+0x1928/0x2580 [mt7915e]
<7>[  203.541451]  __ieee80211_schedule_txq+0xe60/0x1b30 [mac80211]
<7>[  203.547206]  __ieee80211_xmit_fast+0x7b4/0x950 [mac80211]
<7>[  203.552600]  __ieee80211_subif_start_xmit+0x1e8/0x354 [mac80211]
<7>[  203.558603]  ieee80211_subif_start_xmit+0x3c/0x3bc [mac80211]
<7>[  203.564345]  ieee80211_subif_start_xmit_8023+0x318/0x430 [mac80211]
<7>[  203.570606]  dev_hard_start_xmit+0xe4/0x180
<7>[  203.574776]  __dev_queue_xmit+0x968/0xc30
<7>[  203.578769]  dev_queue_xmit+0x10/0x20
<7>[  203.582415]  br_dev_queue_push_xmit+0x9c/0x1b4
<7>[  203.586845]  br_forward_finish+0x98/0xb0
<7>[  203.590752]  __br_forward+0x138/0x1a0
<7>[  203.594399]  br_forward+0x124/0x150
<7>[  203.597873]  br_handle_frame_finish+0x30c/0x4d0
<7>[  203.602386]  br_handle_frame+0x398/0x41c
<7>[  203.606291]  __netif_receive_skb_core.constprop.0+0x254/0xcb0
<7>[  203.612018]  __netif_receive_skb_list_core+0xd4/0x1e0
<7>[  203.617050]  netif_receive_skb_list_internal+0x1b8/0x280
<7>[  203.622343]  napi_complete_done+0x64/0x1a0
<7>[  203.626423]  gro_cell_poll+0x80/0xa0
<7>[  203.629986]  __napi_poll+0x54/0x1b0
<7>[  203.633460]  net_rx_action+0x2a0/0x320
<7>[  203.637192]  _stext+0x10c/0x28c
<7>[  203.640320]  do_softirq+0x8c/0xa0
<7>[  203.643623]  __local_bh_enable_ip+0xa0/0xa4
<7>[  203.647789]  napi_threaded_poll+0x120/0x1a0
<7>[  203.651956]  kthread+0x11c/0x130
<7>[  203.655173]  ret_from_fork+0x10/0x20
<0>[  203.658735] Code: f90002a0 52800002 f90006a1 f900a275 (f9000035) 
<4>[  203.664808] ---[ end trace eb5248042cf7d915 ]---
<0>[  203.673566] Kernel panic - not syncing: Oops: Fatal exception in interrupt
<2>[  203.680420] SMP: stopping secondary CPUs
<0>[  203.684326] Kernel Offset: disabled
<0>[  203.687796] CPU features: 0x0,00000000,20000802
<0>[  203.692309] Memory Limit: none

Possibly also relevant: system log when doing a repeater scan when the system does not crash:

Sun Jan 21 02:59:58 2024 daemon.info gl-repeater[10535]: (repeater.lua:208) scanning...
Sun Jan 21 02:59:59 2024 daemon.err gl-repeater[10535]: (gl-repeater.lua:239) /usr/local/lib/lua/5.3/eco/nl80211.lua:439: attempt to perform bitwise operation on a nil value
Sun Jan 21 03:00:01 2024 daemon.info gl-repeater[11875]: (gl-repeater.lua:253) lua-eco version:	3.2.0
Sun Jan 21 03:00:01 2024 daemon.info gl-repeater[11875]: (gl-repeater.lua: 16) load repeater config...
Sun Jan 21 03:00:01 2024 daemon.info gl-repeater[11875]: (gl-repeater.lua:222) wait ap ready...
Sun Jan 21 03:00:01 2024 daemon.info gl-repeater[11875]: (gl-repeater.lua: 82) load wifi config...
Sun Jan 21 03:00:02 2024 daemon.info gl-repeater[11875]: (repeater.lua:690) switch in	0	seconds...
Sun Jan 21 03:00:02 2024 daemon.info gl-repeater[11875]: (repeater.lua:634) disabled

xize11 · January 20, 2024, 4:41pm

hmm I’m not entirely sure but when I skim fast through your log.

it looks like to me the wifi driver has trouble getting power and the transactions/tx time out.

is also listed in the stacktrace.

above this stacktrace I see that it finds multiple usb devices (2,3) and it sees one as possible tethering.

what is this device?? is this device one device and it was just a swap between the to?, is it connected to a usb hub in some kind?

TapGhoul · January 20, 2024, 4:43pm

This is my phone (a Xiaomi Mi 9 Lite) tethering to the router. Having this disconnected does not seem to make any difference, the logs were created from a point when it was connected.

Also, as some additional info here: when trying to scan and connect via LuCI Network → Wireless → Scan/Connect, I can successfully scan and connect with no issues (though the router does show a warning flag on the repeater, likely cus I bypassed some config, but that’s to be expected and goes away when I disconnect - just trying to help eliminate factors here)

xize11 · January 20, 2024, 4:47pm

hmm I think it must be some type of issue with your wireless settings (the power ones).

then it’s probably not related to your usb, but something else, is your wifi set on 160mhz perhaps?

TapGhoul · January 20, 2024, 4:49pm

Nope. 80mhz. Here’s the settings pages atm (second in next reply):

TapGhoul · January 20, 2024, 4:49pm

TapGhoul · January 20, 2024, 4:51pm

And as a note to skip some tests: switching to a/n/ac/ax and b/g/n/ax does not help here.

xize11 · January 20, 2024, 4:51pm

hmm can you try a lower channel by chance?

your channel has to support the country, but maybe a to high channel may also influence your dBm to a power level it cannot resist?

this is for 5ghz

TapGhoul · January 20, 2024, 4:55pm

No dice. Set both 2.4 and 5 to their lowest channel, just to be safe - there’s plenty going on on those channels - same issue.

xize11 · January 20, 2024, 4:57pm

the only thing I could think of is changing the wpa2/wpa3 mixed to wpa2 or wpa3.

edit: also it came to my attention you use the same ssid under 2.4ghz and 5ghz can you try to split them?, i’ve readed various messages about this causing a issue

if all of this not work, I’m out of idea too maybe @alzhao can help

TapGhoul · January 20, 2024, 5:02pm

Switching to WPA/WPA2-PSK only on both APs didn’t make any difference.
I’m heading off for the night, but I’ll be able to troubleshoot more tomorrow. More than happy to full factory reset, switch to ethernet, apply custom firmware and SSH in to give info if required.

TapGhoul · January 21, 2024, 7:46am

More info! Tried doing some downgrades and upgrades, each time opting not to keep settings and not changing any settings as I migrate around to give it the best chance of working.

I downgraded to 4.5.3, the function works perfectly with no crash and lists nearby networks.
Then upgrading to 4.5.4 this function still operates correctly.
After then upgrading back to 4.5.5, this function breaks. So it seems to be a bug in 4.5.5. I also noticed that on first setting up, repeater is automatically turned on on this firmware, though no clue what it’s connecting to.

The release notes list updated wifi firmware, so maybe it’s related to the firmware update. I’m going to stay on 4.5.4 for now, but if you need further tests I can check it.

TapGhoul · January 25, 2024, 4:01pm

Any word on this issue? @alzhao or others - the 4.5.4 firmware doesn’t auto-connect to USB tethering on connect, so I’d rather upgrade to a newer fixed firmware if I can, and am happy to help accelerate development wherever I can here

Scratch that, 4.5.6 is out! Gonna give it a go.

TapGhoul · January 25, 2024, 4:27pm

It’s no longer crashing the actual router, but I’m still getting repeated wifi drops on boot after a factory reset while it tries to auto-enable repeater and breaks as a result. A copy of the log is below.
In the meantime, I am rolling back to 4.5.4. Repeater works as intended here. If you need any more info, let me know.

Thu Jan 18 20:30:09 2024 daemon.info gl-repeater[8253]: (repeater.lua:208) scanning...
Thu Jan 18 20:30:10 2024 daemon.err gl-repeater[8253]: (gl-repeater.lua:245) /usr/local/lib/lua/5.3/eco/nl80211.lua:439: attempt to perform bitwise operation on a nil value
Thu Jan 18 20:30:12 2024 daemon.info gl-repeater[8294]: (gl-repeater.lua:259) lua-eco version:	3.2.0
Thu Jan 18 20:30:12 2024 daemon.info gl-repeater[8294]: (gl-repeater.lua: 16) load repeater config...
Thu Jan 18 20:30:12 2024 daemon.info gl-repeater[8294]: (gl-repeater.lua:228) wait ap ready...
Thu Jan 18 20:30:12 2024 daemon.info gl-repeater[8294]: (gl-repeater.lua: 82) load wifi config...
Thu Jan 18 20:30:12 2024 daemon.notice hostapd: wlan0: AP-STA-DISCONNECTED 0c:54:15:6e:b4:28
Thu Jan 18 20:30:12 2024 daemon.info hostapd: wlan0: STA 0c:54:15:6e:b4:28 IEEE 802.11: authenticated
Thu Jan 18 20:30:12 2024 daemon.info hostapd: wlan0: STA 0c:54:15:6e:b4:28 IEEE 802.11: authenticated
Thu Jan 18 20:30:12 2024 daemon.info hostapd: wlan0: STA 0c:54:15:6e:b4:28 IEEE 802.11: associated (aid 2)
Thu Jan 18 20:30:13 2024 daemon.notice hostapd: wlan0: AP-STA-CONNECTED 0c:54:15:6e:b4:28 auth_alg=open
Thu Jan 18 20:30:13 2024 daemon.info hostapd: wlan0: STA 0c:54:15:6e:b4:28 RADIUS: starting accounting session EBFC7BFE93E550C8
Thu Jan 18 20:30:13 2024 daemon.info hostapd: wlan0: STA 0c:54:15:6e:b4:28 WPA: pairwise key handshake completed (RSN)
Thu Jan 18 20:30:13 2024 daemon.notice hostapd: wlan0: EAPOL-4WAY-HS-COMPLETED 0c:54:15:6e:b4:28
Thu Jan 18 20:30:13 2024 daemon.info dnsmasq-dhcp[1]: DHCPREQUEST(br-lan) 192.168.8.245 0c:54:15:6e:b4:28
Thu Jan 18 20:30:13 2024 daemon.info dnsmasq-dhcp[1]: DHCPACK(br-lan) 192.168.8.245 0c:54:15:6e:b4:28 Taps-Nuc
Thu Jan 18 20:30:13 2024 daemon.info gl-repeater[8294]: (repeater.lua:690) switch in	0	seconds...
Thu Jan 18 20:30:13 2024 daemon.info gl-repeater[8294]: (repeater.lua:208) scanning...
Thu Jan 18 20:30:14 2024 daemon.err gl-repeater[8294]: (gl-repeater.lua:245) /usr/local/lib/lua/5.3/eco/nl80211.lua:439: attempt to perform bitwise operation on a nil value
Thu Jan 18 20:30:16 2024 daemon.notice hostapd: wlan0: AP-STA-DISCONNECTED 0c:54:15:6e:b4:28
Thu Jan 18 20:30:16 2024 daemon.info gl-repeater[8322]: (gl-repeater.lua:259) lua-eco version:	3.2.0
Thu Jan 18 20:30:16 2024 daemon.info gl-repeater[8322]: (gl-repeater.lua: 16) load repeater config...
Thu Jan 18 20:30:16 2024 daemon.info gl-repeater[8322]: (gl-repeater.lua:228) wait ap ready...
Thu Jan 18 20:30:16 2024 daemon.info hostapd: wlan0: STA 0c:54:15:6e:b4:28 IEEE 802.11: authenticated
Thu Jan 18 20:30:16 2024 daemon.info hostapd: wlan0: STA 0c:54:15:6e:b4:28 IEEE 802.11: authenticated
Thu Jan 18 20:30:16 2024 daemon.info gl-repeater[8322]: (gl-repeater.lua: 82) load wifi config...
Thu Jan 18 20:30:16 2024 daemon.info hostapd: wlan0: STA 0c:54:15:6e:b4:28 IEEE 802.11: associated (aid 2)
Thu Jan 18 20:30:17 2024 daemon.notice hostapd: wlan0: AP-STA-CONNECTED 0c:54:15:6e:b4:28 auth_alg=open
Thu Jan 18 20:30:17 2024 daemon.info hostapd: wlan0: STA 0c:54:15:6e:b4:28 RADIUS: starting accounting session EBFC7BFE93E550C8
Thu Jan 18 20:30:17 2024 daemon.info hostapd: wlan0: STA 0c:54:15:6e:b4:28 WPA: pairwise key handshake completed (RSN)
Thu Jan 18 20:30:17 2024 daemon.notice hostapd: wlan0: EAPOL-4WAY-HS-COMPLETED 0c:54:15:6e:b4:28
Thu Jan 18 20:30:17 2024 daemon.info dnsmasq-dhcp[1]: DHCPREQUEST(br-lan) 192.168.8.245 0c:54:15:6e:b4:28
Thu Jan 18 20:30:17 2024 daemon.info dnsmasq-dhcp[1]: DHCPACK(br-lan) 192.168.8.245 0c:54:15:6e:b4:28 Taps-Nuc
Thu Jan 18 20:30:17 2024 daemon.info gl-repeater[8322]: (repeater.lua:690) switch in	0	seconds...
Thu Jan 18 20:30:17 2024 daemon.info gl-repeater[8322]: (repeater.lua:208) scanning...
Thu Jan 18 20:30:19 2024 daemon.err gl-repeater[8322]: (gl-repeater.lua:245) /usr/local/lib/lua/5.3/eco/nl80211.lua:439: attempt to perform bitwise operation on a nil value
Thu Jan 18 20:30:21 2024 daemon.info gl-repeater[8355]: (gl-repeater.lua:259) lua-eco version:	3.2.0
Thu Jan 18 20:30:21 2024 daemon.info gl-repeater[8355]: (gl-repeater.lua: 16) load repeater config...
Thu Jan 18 20:30:21 2024 daemon.info gl-repeater[8355]: (gl-repeater.lua:228) wait ap ready...
Thu Jan 18 20:30:21 2024 daemon.info gl-repeater[8355]: (gl-repeater.lua: 82) load wifi config...
Thu Jan 18 20:30:21 2024 daemon.notice hostapd: wlan0: AP-STA-DISCONNECTED 0c:54:15:6e:b4:28
Thu Jan 18 20:30:22 2024 daemon.info gl-repeater[8355]: (repeater.lua:690) switch in	0	seconds...
Thu Jan 18 20:30:22 2024 daemon.info hostapd: wlan0: STA 0c:54:15:6e:b4:28 IEEE 802.11: authenticated
Thu Jan 18 20:30:22 2024 daemon.info hostapd: wlan0: STA 0c:54:15:6e:b4:28 IEEE 802.11: authenticated
Thu Jan 18 20:30:22 2024 daemon.info hostapd: wlan0: STA 0c:54:15:6e:b4:28 IEEE 802.11: authenticated
Thu Jan 18 20:30:22 2024 daemon.info gl-repeater[8355]: (repeater.lua:208) scanning...
Thu Jan 18 20:30:22 2024 daemon.info hostapd: wlan0: STA 0c:54:15:6e:b4:28 IEEE 802.11: associated (aid 2)
Thu Jan 18 20:30:23 2024 daemon.err gl-repeater[8355]: (gl-repeater.lua:245) /usr/local/lib/lua/5.3/eco/nl80211.lua:439: attempt to perform bitwise operation on a nil value
Thu Jan 18 20:30:23 2024 daemon.notice hostapd: wlan0: AP-STA-CONNECTED 0c:54:15:6e:b4:28 auth_alg=open
Thu Jan 18 20:30:23 2024 daemon.info hostapd: wlan0: STA 0c:54:15:6e:b4:28 RADIUS: starting accounting session EBFC7BFE93E550C8
Thu Jan 18 20:30:23 2024 daemon.info hostapd: wlan0: STA 0c:54:15:6e:b4:28 WPA: pairwise key handshake completed (RSN)
Thu Jan 18 20:30:23 2024 daemon.notice hostapd: wlan0: EAPOL-4WAY-HS-COMPLETED 0c:54:15:6e:b4:28
Thu Jan 18 20:30:23 2024 daemon.info dnsmasq-dhcp[1]: DHCPREQUEST(br-lan) 192.168.8.245 0c:54:15:6e:b4:28
Thu Jan 18 20:30:23 2024 daemon.info dnsmasq-dhcp[1]: DHCPACK(br-lan) 192.168.8.245 0c:54:15:6e:b4:28 Taps-Nuc
Thu Jan 18 20:30:25 2024 daemon.info gl-repeater[8383]: (gl-repeater.lua:259) lua-eco version:	3.2.0
Thu Jan 18 20:30:25 2024 daemon.info gl-repeater[8383]: (gl-repeater.lua: 16) load repeater config...
Thu Jan 18 20:30:25 2024 daemon.info gl-repeater[8383]: (gl-repeater.lua:228) wait ap ready...
Thu Jan 18 20:30:25 2024 daemon.info gl-repeater[8383]: (gl-repeater.lua: 82) load wifi config...
Thu Jan 18 20:30:26 2024 daemon.info gl-repeater[8383]: (repeater.lua:690) switch in	0	seconds...
Thu Jan 18 20:30:26 2024 daemon.info gl-repeater[8383]: (repeater.lua:208) scanning...
Thu Jan 18 20:30:27 2024 daemon.err gl-repeater[8383]: (gl-repeater.lua:245) /usr/local/lib/lua/5.3/eco/nl80211.lua:439: attempt to perform bitwise operation on a nil value
Thu Jan 18 20:30:29 2024 daemon.notice hostapd: wlan0: AP-STA-DISCONNECTED 0c:54:15:6e:b4:28
Thu Jan 18 20:30:29 2024 daemon.info hostapd: wlan0: STA 0c:54:15:6e:b4:28 IEEE 802.11: authenticated
Thu Jan 18 20:30:29 2024 daemon.info hostapd: wlan0: STA 0c:54:15:6e:b4:28 IEEE 802.11: associated (aid 2)
Thu Jan 18 20:30:29 2024 daemon.notice hostapd: wlan0: AP-STA-CONNECTED 0c:54:15:6e:b4:28 auth_alg=open
Thu Jan 18 20:30:29 2024 daemon.info hostapd: wlan0: STA 0c:54:15:6e:b4:28 RADIUS: starting accounting session EBFC7BFE93E550C8
Thu Jan 18 20:30:29 2024 daemon.info hostapd: wlan0: STA 0c:54:15:6e:b4:28 WPA: pairwise key handshake completed (RSN)
Thu Jan 18 20:30:29 2024 daemon.notice hostapd: wlan0: EAPOL-4WAY-HS-COMPLETED 0c:54:15:6e:b4:28
Thu Jan 18 20:30:29 2024 daemon.info dnsmasq-dhcp[1]: DHCPREQUEST(br-lan) 192.168.8.245 0c:54:15:6e:b4:28
Thu Jan 18 20:30:29 2024 daemon.info dnsmasq-dhcp[1]: DHCPACK(br-lan) 192.168.8.245 0c:54:15:6e:b4:28 Taps-Nuc
Thu Jan 18 20:30:29 2024 daemon.err gl-ngx-session[1848]: (gl-ngx-session:304) session more than 	5	, clean the last inactive
Thu Jan 18 20:30:29 2024 daemon.info gl-repeater[8397]: (gl-repeater.lua:259) lua-eco version:	3.2.0
Thu Jan 18 20:30:29 2024 daemon.info gl-repeater[8397]: (gl-repeater.lua: 16) load repeater config...
Thu Jan 18 20:30:29 2024 daemon.info gl-repeater[8397]: (gl-repeater.lua:228) wait ap ready...
Thu Jan 18 20:30:29 2024 daemon.info gl-repeater[8397]: (gl-repeater.lua: 82) load wifi config...
Thu Jan 18 20:30:30 2024 daemon.info gl-repeater[8397]: (repeater.lua:690) switch in	0	seconds...
Thu Jan 18 20:30:30 2024 daemon.info gl-repeater[8397]: (repeater.lua:208) scanning...
Thu Jan 18 20:30:31 2024 daemon.err gl-repeater[8397]: (gl-repeater.lua:245) /usr/local/lib/lua/5.3/eco/nl80211.lua:439: attempt to perform bitwise operation on a nil value
Thu Jan 18 20:30:33 2024 daemon.notice hostapd: wlan0: AP-STA-DISCONNECTED 0c:54:15:6e:b4:28
Thu Jan 18 20:30:33 2024 daemon.info hostapd: wlan0: STA 0c:54:15:6e:b4:28 IEEE 802.11: authenticated
Thu Jan 18 20:30:33 2024 daemon.info hostapd: wlan0: STA 0c:54:15:6e:b4:28 IEEE 802.11: associated (aid 2)
Thu Jan 18 20:30:33 2024 daemon.notice hostapd: wlan0: AP-STA-CONNECTED 0c:54:15:6e:b4:28 auth_alg=open
Thu Jan 18 20:30:33 2024 daemon.info hostapd: wlan0: STA 0c:54:15:6e:b4:28 RADIUS: starting accounting session EBFC7BFE93E550C8
Thu Jan 18 20:30:33 2024 daemon.info hostapd: wlan0: STA 0c:54:15:6e:b4:28 WPA: pairwise key handshake completed (RSN)
Thu Jan 18 20:30:33 2024 daemon.notice hostapd: wlan0: EAPOL-4WAY-HS-COMPLETED 0c:54:15:6e:b4:28
Thu Jan 18 20:30:33 2024 daemon.info dnsmasq-dhcp[1]: DHCPREQUEST(br-lan) 192.168.8.245 0c:54:15:6e:b4:28
Thu Jan 18 20:30:33 2024 daemon.info dnsmasq-dhcp[1]: DHCPACK(br-lan) 192.168.8.245 0c:54:15:6e:b4:28 Taps-Nuc
Thu Jan 18 20:30:33 2024 daemon.info gl-repeater[8456]: (gl-repeater.lua:259) lua-eco version:	3.2.0
Thu Jan 18 20:30:33 2024 daemon.info gl-repeater[8456]: (gl-repeater.lua: 16) load repeater config...
Thu Jan 18 20:30:33 2024 daemon.info gl-repeater[8456]: (gl-repeater.lua:228) wait ap ready...
Thu Jan 18 20:30:33 2024 daemon.info gl-repeater[8456]: (gl-repeater.lua: 82) load wifi config...
Thu Jan 18 20:30:34 2024 daemon.info gl-repeater[8456]: (repeater.lua:626) disabled by user
Thu Jan 18 20:30:34 2024 daemon.info gl-repeater[8456]: (repeater.lua:690) switch in	0	seconds...
Thu Jan 18 20:30:34 2024 daemon.info gl-repeater[8456]: (repeater.lua:634) disabled

Info from kernel on PC side:

[  149.460232] wlp6s0: authenticate with 94:83:c4:a2:10:c6
[  149.470775] wlp6s0: send auth to 94:83:c4:a2:10:c6 (try 1/3)
[  149.478699] wlp6s0: authenticate with 94:83:c4:a2:10:c6
[  149.485378] wlp6s0: send auth to 94:83:c4:a2:10:c6 (try 1/3)
[  149.486155] wlp6s0: authenticated
[  149.489355] wlp6s0: associate with 94:83:c4:a2:10:c6 (try 1/3)
[  149.506253] wlp6s0: RX AssocResp from 94:83:c4:a2:10:c6 (capab=0x111 status=0 aid=1)
[  149.519224] wlp6s0: associated
[  149.529181] wlp6s0: Limiting TX power to 21 (24 - 3) dBm as advertised by 94:83:c4:a2:10:c6
[  152.822319] wlp6s0: deauthenticated from 94:83:c4:a2:10:c6 (Reason: 3=DEAUTH_LEAVING)
[  153.852236] wlp6s0: authenticate with 94:83:c4:a2:10:c6
[  153.863628] wlp6s0: send auth to 94:83:c4:a2:10:c6 (try 1/3)
[  153.917211] wlp6s0: send auth to 94:83:c4:a2:10:c6 (try 2/3)
[  153.962533] wlp6s0: send auth to 94:83:c4:a2:10:c6 (try 3/3)
[  154.020365] wlp6s0: authentication with 94:83:c4:a2:10:c6 timed out
[  204.469484] wlp6s0: authenticate with 94:83:c4:a2:10:c6
[  204.478517] wlp6s0: send auth to 94:83:c4:a2:10:c6 (try 1/3)
[  204.485159] wlp6s0: authenticated
[  204.489318] wlp6s0: associate with 94:83:c4:a2:10:c6 (try 1/3)
[  204.499004] wlp6s0: RX AssocResp from 94:83:c4:a2:10:c6 (capab=0x11 status=0 aid=1)
[  204.501696] wlp6s0: associated
[  226.164961] wlp6s0: authenticate with 94:83:c4:a2:10:c6
[  226.173265] wlp6s0: send auth to 94:83:c4:a2:10:c6 (try 1/3)
[  226.204081] wlp6s0: send auth to 94:83:c4:a2:10:c6 (try 2/3)
[  226.261423] wlp6s0: send auth to 94:83:c4:a2:10:c6 (try 3/3)
[  226.313534] wlp6s0: authentication with 94:83:c4:a2:10:c6 timed out
[  243.273782] wlp6s0: authenticate with 94:83:c4:a2:10:c5
[  243.273809] wlp6s0: 80 MHz not supported, disabling VHT
[  243.281125] wlp6s0: send auth to 94:83:c4:a2:10:c5 (try 1/3)
[  243.289469] wlp6s0: authenticated
[  243.292650] wlp6s0: associate with 94:83:c4:a2:10:c5 (try 1/3)
[  243.300066] wlp6s0: RX AssocResp from 94:83:c4:a2:10:c5 (capab=0x431 status=0 aid=1)
[  243.312735] wlp6s0: associated
[  250.589384] wlp6s0: authenticate with 94:83:c4:a2:10:c5
[  250.589405] wlp6s0: 80 MHz not supported, disabling VHT
[  250.597089] wlp6s0: send auth to 94:83:c4:a2:10:c5 (try 1/3)
[  250.702641] wlp6s0: send auth to 94:83:c4:a2:10:c5 (try 2/3)
[  250.771131] wlp6s0: authenticated
[  250.772642] wlp6s0: associate with 94:83:c4:a2:10:c5 (try 1/3)
[  250.787379] wlp6s0: RX AssocResp from 94:83:c4:a2:10:c5 (capab=0x431 status=0 aid=1)
[  250.790225] wlp6s0: associated
[  254.815682] wlp6s0: authenticate with 94:83:c4:a2:10:c5
[  254.815711] wlp6s0: 80 MHz not supported, disabling VHT
[  254.822863] wlp6s0: send auth to 94:83:c4:a2:10:c5 (try 1/3)
[  254.925975] wlp6s0: send auth to 94:83:c4:a2:10:c5 (try 2/3)
[  254.983537] wlp6s0: authenticated
[  254.986052] wlp6s0: associate with 94:83:c4:a2:10:c5 (try 1/3)
[  255.000138] wlp6s0: RX AssocResp from 94:83:c4:a2:10:c5 (capab=0x431 status=0 aid=1)
[  255.002989] wlp6s0: associated
[  258.939546] wlp6s0: authenticate with 94:83:c4:a2:10:c5
[  258.939577] wlp6s0: 80 MHz not supported, disabling VHT
[  258.947617] wlp6s0: send auth to 94:83:c4:a2:10:c5 (try 1/3)
[  259.055982] wlp6s0: send auth to 94:83:c4:a2:10:c5 (try 2/3)
[  259.080287] wlp6s0: authenticated
[  259.082654] wlp6s0: associate with 94:83:c4:a2:10:c5 (try 1/3)
[  259.096801] wlp6s0: RX AssocResp from 94:83:c4:a2:10:c5 (capab=0x431 status=0 aid=1)
[  259.100461] wlp6s0: associated
[  263.236203] wlp6s0: authenticate with 94:83:c4:a2:10:c5
[  263.236229] wlp6s0: 80 MHz not supported, disabling VHT
[  263.243825] wlp6s0: send auth to 94:83:c4:a2:10:c5 (try 1/3)
[  263.345999] wlp6s0: send auth to 94:83:c4:a2:10:c5 (try 2/3)
[  263.374883] wlp6s0: authenticated
[  263.376022] wlp6s0: associate with 94:83:c4:a2:10:c5 (try 1/3)
[  263.392523] wlp6s0: RX AssocResp from 94:83:c4:a2:10:c5 (capab=0x431 status=0 aid=1)
[  263.394874] wlp6s0: associated
[  268.869306] wlp6s0: authenticate with 94:83:c4:a2:10:c5
[  268.869326] wlp6s0: 80 MHz not supported, disabling VHT
[  268.877397] wlp6s0: send auth to 94:83:c4:a2:10:c5 (try 1/3)
[  268.982646] wlp6s0: send auth to 94:83:c4:a2:10:c5 (try 2/3)
[  269.088056] wlp6s0: send auth to 94:83:c4:a2:10:c5 (try 3/3)
[  269.189295] wlp6s0: authentication with 94:83:c4:a2:10:c5 timed out
[  292.751767] wlp6s0: authenticate with 94:83:c4:a2:10:c5
[  292.751801] wlp6s0: 80 MHz not supported, disabling VHT
[  292.759691] wlp6s0: send auth to 94:83:c4:a2:10:c5 (try 1/3)
[  292.768635] wlp6s0: authenticated
[  292.769304] wlp6s0: associate with 94:83:c4:a2:10:c5 (try 1/3)
[  292.783358] wlp6s0: RX AssocResp from 94:83:c4:a2:10:c5 (capab=0x431 status=0 aid=1)
[  292.786255] wlp6s0: associated

My system has no issues normally with 80MHz, nor does the router, so not sure what’s going on. On 4.5.4 I have no such issues.

gfondeur · January 25, 2024, 4:42pm

4.5.4 it’s more stable for me overall than 4.5.5 or 4.5.6

TapGhoul · February 5, 2024, 11:02pm

Hey! Any updates on this issue? It’s holding me back from latest f/w.

alzhao · February 6, 2024, 9:33am

We are working on a MTK proprietory wifi driver firmware. Not sure if you want to try.

TapGhoul · February 6, 2024, 1:41pm

If me trying can help test this faster, feel free. I can test and then worst case uboot back. Happy to provide any kinds of logs/monitoring/etc, only caveat is right now all internet is through USB tethering, no ethernet based WAN. But I’m happy to test out whatever firmware to see if I run into the same crashes and run tests.

alzhao · February 7, 2024, 2:29am

Use with caution. I didn’t test this by myself yet.

TapGhoul · February 7, 2024, 5:46pm

I wanted to give it a go but couldn’t get my PC to load the u-boot page, so I am unable to test with confidence, which is unfortunate. Got it booted into it but just couldn’t get the page to load. I will need to wait for a tested release, sorry. I really did want to give this a test