Yopo
February 15, 2022, 8:42pm
1
Hello everyone, I’m kind of going crazy over this.
I got an optical fiber connection from Deutch Telekom (Magenta), Telekon provided the modem. I have the user/password to initiate the PPPoE connection but when I do from the Brume interface, it fails. That’s normal because Telekom needs a VLAN tagging to 7.
I checked the Openwrt guide but I still can’t get it to work with the same config. I tried to access Switch in Luci but there is none.
At the moment I use my former Synology RT2600 but I really want to fit the Brume instead (and my Beryl maybe later).
Could somebody guide me through the process to get it to work?
Thank you
alzhao
February 16, 2022, 9:03am
2
Yopo
February 16, 2022, 9:04pm
3
Thanks @alzhao , I’m still unsure how to proceed with the tagging on the Brume.
At the moment I connected a Beryl instead and was able to get it to work with the following configuration of my /etc/config/network:
config interface ‘loopback’
option ifname ‘lo’
option proto ‘static’
option ipaddr ‘127.0.0.1’
option netmask ‘255.0.0.0’
config globals ‘globals’
option ula_prefix ‘fde0:9e75:fc2f::/48’
config interface ‘lan’
option type ‘bridge’
option ifname ‘eth0.1’
option proto ‘static’
option netmask ‘255.255.255.0’
option ip6assign ‘60’
option hostname ‘GL-MT1300-727’
option ipaddr ‘192.168.0.1’
config interface ‘wan’
option ipv6 ‘0’
option proto ‘pppoe’
option username ‘username***’
option password ‘password***’
option metric ‘10’
option disabled ‘0’
option ifname ‘eth0.7’
config interface ‘wan6’
option ifname ‘eth0.2’
option proto ‘dhcpv6’
option disabled ‘1’
config switch
option name ‘switch0’
option reset ‘1’
option enable_vlan ‘1’
config switch_vlan
option device ‘switch0’
option vlan ‘1’
config switch_vlan
option device ‘switch0’
option vlan ‘2’
option ports ‘6t 4’
option vid ‘2’
config interface ‘guest’
option ifname ‘guest’
option type ‘bridge’
option proto ‘static’
option ipaddr ‘192.168.9.1’
option netmask ‘255.255.255.0’
option ip6assign ‘60’
option bridge_empty ‘1’
config device ‘wan_dev’
option name ‘eth0.2’
option macaddr ‘69:96:r2:1f:c7:25’
config device ‘lan_dev’
option name ‘eth0.1’
option macaddr ‘69:96:r2:1f:c7:26’
config switch_vlan
option device ‘switch0’
option vlan ‘3’
option ports ‘6t 4t’
option vid ‘7’
How to achieve similar setup on the Brume since vlan is not managed by swconfig?
lizh
February 17, 2022, 8:37am
4
hi Yopo:
BRUME vlan is not managed by swconfig.It is different form Beryl.
For BRUME,You need add:
config interface ‘wan_pppoe’
option ipv6 ‘0’
option proto ‘pppoe’
option username ‘username***’
option password ‘password***’
option metric ‘10’
option disabled ‘0’
option ifname ‘wan.7’
Yopo
February 17, 2022, 7:51pm
5
Thank you @lizh
option ifname ‘wan.7’
is exactly what was needed!