Firmware 3.201_beta3

[defibos]

Hi, thanks for answering so fast.
I knew MT300N-v2 uses a mtk blob as driver, what I mean is whether they are currently providing updates to the blob or they are concentrated in newer systems (wifi 5 & wifi 6) leaving the current blob as it is. Is there any real expectation of wpa3 support in 1y-2y?
Thanks

[Bilou]

Installed with no glitch on E750. Luci working 100% fine
Just noticed that the cellular strength signal bar bug is still there (full bars always displayed on LCD although less bars in web interface)

[luochongjun]

Has been fixed in the Beta4.

[luochongjun]

Thanks for reminding.
Has been fixed in the Beta4.

[elorimer]

All looking good here, except the VPN shield behavior for OpenVPN client is stuck on the “!”

IGMP and DLNA are not for the MT1300? Of no consequence to me but curious.

[aelserafy]

Does this beta address the issue mentioned here on Slate? As it wasn’t fixed in the beta2…
Also, where can I get the *.tar for the AR300m with the 128 MB nand?

[luochongjun]

The MT1300 already supports both of these functions in the 3.200 firmware.

[luochongjun]

Yes, the problem was fixed in the beta4 version, the beta4 version of ar300m is here.

[luochongjun]

Has been fixed in version 03.19

[Max3]

Any way to continue to use DLNA media server and network shares on AR750 and MT300N-v2 (or other limited flash devices) with latest firmware? Trying to download them results in a “not enough flash space” message… Time to think of using exroot?

[modumb]

just want to draw attention to a serious regression I’ve noticed on the latest betas:

3.201beta2 - AR750S - instability issues

I have been using 3.201beta2 since it was posted on the server. Since then, the experience with my slate has been quite unreliable: My huawei e1752 usb modem sometimes stops working and does not always reconnect even after a full reboot of the slate The slate sometimes spontaneously reboots As a result, I have not had a single uptime longer than 18 hours since using the firmware - normally the slate is left running 24/7 and would have days or weeks of uninterrupted uptime on 3.105 I…

3.201beta2 - AR750S - instability issues

To continue the report… the 3g modem was never stable under beta2 as it is/was with 3.105. Unfortunately, under beta4 of 3.201 the modem is completely unusable. Starting each time from a clean firmware (no settings retained), I have not yet managed to make the USB modem work for longer than 20 minutes and then only for just one time (did not work after reboot or ever again). I have spent an hour trying every approach I could think of to make it work again only once but I cannot make it happen…

EDIT:

at least with beta 4 there is some information showing up in the logs:

Fri Mar 19 10:37:48 2021 daemon.err pppd[9265]: Connect script failed
Fri Mar 19 10:37:49 2021 daemon.info pppd[9265]: Exit.
Fri Mar 19 10:37:49 2021 daemon.notice netifd: Interface ‘modem_1_1’ is now down
Fri Mar 19 10:37:49 2021 daemon.notice netifd: Interface ‘modem_1_1’ is setting up now
Fri Mar 19 10:37:51 2021 daemon.notice netifd: modem_1_1 (9315): Trying to set mode
Fri Mar 19 10:37:52 2021 daemon.notice netifd: modem_1_1 (9315): cat: can’t open ‘/tmp/modem.1-1/signal’: No such file or directory
Fri Mar 19 10:37:52 2021 daemon.notice pppd[9520]: pppd 2.4.7 started by root, uid 0
Fri Mar 19 10:37:53 2021 local2.info chat[9530]: abort on (BUSY)
Fri Mar 19 10:37:53 2021 local2.info chat[9530]: abort on (NO CARRIER)
Fri Mar 19 10:37:53 2021 local2.info chat[9530]: abort on (ERROR)
Fri Mar 19 10:37:53 2021 local2.info chat[9530]: report (CONNECT)
Fri Mar 19 10:37:53 2021 local2.info chat[9530]: timeout set to 10 seconds
Fri Mar 19 10:37:53 2021 local2.info chat[9530]: send (AT+CGDCONT=1,“IP”,“orange”^M)
Fri Mar 19 10:37:53 2021 local2.info chat[9530]: timeout set to 30 seconds
Fri Mar 19 10:37:53 2021 local2.info chat[9530]: expect (OK)
Fri Mar 19 10:37:54 2021 local2.info chat[9530]: “orange”^M^M
Fri Mar 19 10:37:54 2021 local2.info chat[9530]: OK
Fri Mar 19 10:37:54 2021 local2.info chat[9530]: – got it
Fri Mar 19 10:37:54 2021 local2.info chat[9530]: send (ATD991#^M)
Fri Mar 19 10:37:54 2021 local2.info chat[9530]: expect (CONNECT)
Fri Mar 19 10:37:54 2021 local2.info chat[9530]: ^M
Fri Mar 19 10:37:54 2021 local2.info chat[9530]: ATD99**1#^M^M
Fri Mar 19 10:37:54 2021 local2.info chat[9530]: NO CARRIER
Fri Mar 19 10:37:54 2021 local2.info chat[9530]: – failed
Fri Mar 19 10:37:54 2021 local2.info chat[9530]: Failed (NO CARRIER)
Fri Mar 19 10:37:54 2021 daemon.err pppd[9520]: Connect script failed
Fri Mar 19 10:37:55 2021 daemon.info pppd[9520]: Exit.
Fri Mar 19 10:37:55 2021 daemon.notice netifd: Interface ‘modem_1_1’ is now down

[elorimer]

sqm won’t install–fails kernel dependency

this is the 3.18 build at 14:21 gmt for MT1300 (3.19 snapshot)

[alzhao]

Working on beta4 released Mar 18th, AR750s and sqm is OK.

[Rubycon]

With update qsdk-s1300-3.201-0319.img on S1300, nothing changed at all. Still version 3.105. Also same version of Adguard Home as before (v0.105.2).

[aelserafy]

I can confirm this. Tethering is not usable using Slate and beta4!

[luochongjun]

Have you installed all the optional plugs at the same time? Or do you have too many VPN profiles taking up space?

[luochongjun]

It looks like a problem with the power supply. Can you tell me the specification of the power adapter?

[luochongjun]

Is it Android or iOS, can you tell me the system version?

[luochongjun]

Fixed MT1300 kmod software library, please update and try again.

[luochongjun]

I tried to upgrade from the 3.105 reserved configuration and it worked fine. I didn’t have AdGuardHome on, but I don’t think it will affect the upgrade.