Need your help in testing Flint 2 (GL-MT6000) new beta firmware v4.5.7

Just flashed back and works fine on my dumb ap, its safe to keep settings?

Anyway speedtest on cloudflare on my 2.4ghz network:

This is from around 15 meters away, the upload may be on a low side but need to recheck this a bit closer.

speedtest reports:

I think you guys onto something here, 4.5.7 from 03/05 it’s been really stable for me so far and my latency it’s been cut in half, it’s screaming fast on all my test that’s really good.

Full disclaimer, I’m using my Flint2 as AP with double NAT until I feel it’s ready to be my gateway :person_shrugging:

ps. I really wish you guys are able to bring the firmware to use a more updated version of the OpenWRT base.

1 Like

I can say that the improvement, especially in terms of stability, this point has improved a lot! I’m already running the new beta version since its launch yesterday!

My 2.4Ghz network became more stable and performance improved significantly. It’s not ideal yet, but it’s better!

I also stopped having problems with ppoe!

Best regards!


HI. Is fw 4.5.7 dated 05-03-2024 based on openwrt 23.05?

27 posts were split to a new topic: Flint 2 - Beta 4.5.7 Wi-Fi power?

I just upgrade to the latest beta (release5) but the previous beta seemed really stable, no issues at all, the connection drops I was having (likely related to DNS) on 4.5.6 are gone away now, so definitely good progress has been made

There appears to be an issue with GoodCloud. I have it enabled, however, it shows offline on the goodcloud portal. I was previously running it fine on 4.5.6. Going to 4.5.7 beta I did a clean install and configured everything once again. Below are the logs, with sensitive information redacted.

Fri Mar  8 17:50:14 2024 daemon.err gl-cloud[27414]: (gl-cloud:255) fetch server fail:-4	token invalid
Fri Mar  8 17:50:14 2024 daemon.err gl-cloud[27414]: (gl-cloud:510) reconnect mqtt in 160s...
Fri Mar  8 17:52:54 2024 gl-cloud[27414]: (gl-cloud:164) fetch ca from:
Fri Mar  8 17:52:54 2024 gl-cloud[27414]: (gl-cloud:230) fetch server from:

Please try this:

Oh, thanks a lot! That worked :slight_smile: So I gladly report that I have no issues. Wired and wireless speeds are great with all of my devices so far. AdGuardHome working well, Wireguard VPN client and PPPoE as well, although I did change some configs as it was suggested for PPPoE in the main MT-6000 thread.

1 Like

I’m getting impressive iperf3 results reaching upto 1.32 Gbit when using my Pixel 7 and running the iperf3 server directly on the GL-MT6000.

5GHz, 160MHz + irqbalance enabled (but i don’t think irqbalance makes a huge difference).

The Wireguard WiFi speed is with the Pixel 7 better compared to my AX210 WiFi adapter.

The LAN Wireguard speed is still the same and reaching upto 850 Mbit.

1 Like

Firmware 4.5.7 (5/Mar/23)

My Google Pixel 7 is going offline and online again by no reason, randomly.

1 Like

How often is this happening for you? What are your WiFi settings? E.g. channel, bandwith, encryption, wifi band, etc.

I lost internet connection on some devices today, I rebooted the router and now it’s working, I kept settings while updating the v4.5.7 betas, not sure what happened :thinking:

1 Like

When this happens, you need to share the log here

I couldn’t, I was sending a huge work project and needed connection ASAP… next time I will

v4.5.7 dockerd can’t be installed “cannot find dependency kmod-dm”.
serious problem, being able to run docker is the main reason to get GL-MT6000 for the 1gb memory

1 Like

v4.5.6. wifi speed drops to almost freezing for 1-2 seconds every 30-60 seconds. does not affect file transfer, browsing, but making network gaming not playable at all.

v4.5.7 (3/4/2024) fixed it. hope it stays this way.

You should research better, :person_facepalming:

Please save us the crying about something you can’t install/run because your lack of research before you buy it contact CS and request a return, just my two cents :person_shrugging: